manualshive.com logo in svg

Larco 23365300, Руководство пользователя, Страница: 15 / 15

Поделиться
Скачать
Larco 23365300 Скачать руководство пользователя страница 15

Certifications and Standards

EC Declaration of Conformity (DoC)

ATEK 

Access Technologies

 herewith declares that the MAX1524 and MAX2324 Safety Mat Monitoring Modules are in

 

conformity with the provisions of the Machinery Directive 2006/42/EC and all essential health and safety requirements

 

have been met.

Representative in EU: Peter Mertens, Managing Director Banner Engineering Europe. Address: Park Lane, Culliganlaan 2F,

1831 Diegem, Belgium.

Standards and Regulations

The list of standards below is included as a convenience for users of this device. Inclusion of the standards below does not

imply that the device complies specifically with any standard, other than those specified in the Specifications section of this

manual.

U.S. Application Standards

ANSI B11.0 Safety of Machinery, General Requirements, and Risk Assessment

ANSI B11.19 Performance Criteria for Safeguarding

ANSI NFPA 79 Electrical Standard for Industrial Machinery

International/European Standards

ISO 12100 Safety of Machinery – General Principles for Design — Risk Assessment and Risk Reduction

IEC 60204-1 Electrical Equipment of Machines Part 1: General Requirements

ISO 13856-1 (EN1760-1), Safety of Machinery – Pressure-Sensitive Protective Devices

ISO 13855 (EN 999) The Positioning of Protective Equipment in Respect to Approach Speeds of Parts of the Human Body

IEC 61508 Functional Safety of Electrical/Electronic/Programmable Electronic Safety-Related Systems

IEC 62061 Functional Safety of Safety-Related Electrical, Electronic and Programmable Control Systems

ISO 13849-1 (EN 954-1) Safety-Related Parts of Control Systems

IEC 60947-1 Low Voltage Switchgear – General Rules

IEC 60947-5-1 Low Voltage Switchgear – Electromechanical Control Circuit Devices

IEC 60947-5-5 Low Voltage Switchgear – Electrical Emergency Stop Device with Mechanical Latching Function

IEC 60529 Degrees of Protection Provided by Enclosures

ATEK 

Access Technologies

 Limited Warranty

Unless stipulated differently in Seller’s quotation, Goods are warranted for twelve (12) months from the date of shipment by Seller.

Products purchased by Seller from a third party for resale to Buyer (“Resale Products”) shall carry only the warranty extended by the

original manufacturer. Buyer agrees that Seller has no liability for Resale Products beyond making a reasonable commercial effort to

arrange for procurement and shipping of the Resale Products. If Buyer discovers any warranty defects and notifies Seller thereof in

writing during the applicable warranty period, Seller shall, at its option, repair or replace F.O.B. point of manufacture that portion of

the Goods found by Seller to be defective, or refund the purchase price of the defective portion of the Goods. All replacements or

repairs necessitated by inadequate maintenance, normal wear and usage, unsuitable power sources or environmental conditions,

accident, misuse, improper installation, modification, repair, use of unauthorized replacement parts, improper storage or handling, or

any other cause not the fault of Seller are not covered by this limited warranty, and shall be at Buyer’s expense. Seller shall not be

obligated to pay any costs or charges incurred by Buyer or any other party except as may be agreed upon in writing in advance by

Seller. All costs of dismantling, reinstallation and freight and the time and expenses of Seller’s personnel and representatives for site

travel and diagnosis under this warranty clause shall be borne by Buyer unless accepted in writing by Seller. Goods repaired and parts

replaced by Seller during the warranty period shall be in warranty for the remainder of the original warranty period or ninety (90)

days, whichever is longer. This limited warranty is the only warranty made by Seller and can be amended only in a writing signed by

Seller. THE WARRANTIES AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE. THERE ARE NO REPRESENTATIONS OR WARRANTIES

OF ANY KIND, EXPRESS OR IMPLIED, AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE OR ANY OTHER MATTER WITH

RESPECT TO ANY OF THE GOODS OR SERVICES.

MAX1524 and MAX2324 Safety Mat Monitoring Modules

www.LARCO.com   TEL: 800-523-6996

Содержание 23365300
















Отзывы:

Нет отзывов