Lanzar OPTIX-2B Скачать руководство пользователя страница 11

1. There is an audible distortion at a low

volume level.

PROBLEM

POSSIBLE CAUSE

• Output levels NOT set correctly.
• Crossover frequencies NOT set correctly.
• Check for shorts on the speaker leads.

2. A whining sound can be heard through the

speakers when the audio system is at low
volume with the engine running. The whining
noise remains unchanged or seems to
disappear when the volume level is
increased.

3. There is a "motor boating" type of sound

when the engine is running and the audio
system volume is set at a reasonably high
level.

• Check the red power wire. It muse be

connected directly to the battery.

• Check the system's ground point It muse

make good contact with chassis ground
(bare metal).

• The radio and the CROSSOVER must be

grounded at the same reference point.

• Check the red power wire. It must be

connected directly to the battery.

• Check the system's ground point. It must

make good contact with chassis ground
(bare metal).

9

T B O U B L E   S H O O T I N G   G U I D E

4. High squeal noise from speakers

• This is almost always caused by a poorly -

grounded RCA patch cord.

Содержание OPTIX-2B













Отзывы: