Lantronix PNT-SG3FS Скачать руководство пользователя страница 24

Страница: 24 / 27

9. Antenna Recommendations

PNT-SG3FS GNSS Module Hardware User Guide

Antenna Recommendations

Patch Antenna

Patch antennas have different sizes – 25×25mm, 18×18mm and 12×12mm.
They have the advantage to be cheap, with good efficiency and highly directive. They can be

used when mounted on horizontal support.
Larger antennas provide better performance.

Patch Antenna on the Opposite Side of the PNT-SG3FS

Patch antennas can be pin soldered on the opposite side of the PCB as the PNT-SG3FS and

other RF components, as shown in Figure 15 below.

Figure 15: Antenna and PNT-SG3FS - Opposite Placement

Table 5 below provides information on compatible patch antennas (opposite side mount).

Manufacturer

Part Number

Constellation

Size

Taoglas

CGGBP.25.4.A.02

GPS+Beidou

25×25mm

Taoglas

CGGBP.25.2.A.02

GPS+Beidou

25×25mm

Taoglas

CGGP.18.4.C.02

GPS+Glonass

18×18mm

Yageo

ANT2525B00DT1516S

GPS+Glonass

18×18mm

Yageo

ANT1818B00CT1575S

GPS+Glonass

25×25mm

Table 5. PNT-SG3FS Compatible Patch Antennas (Opposite Side Mount)

Содержание PNT-SG3FS




























Результаты поиска

Содержание PNT-SG3FS

Отзывы:

Бренды по названию

Популярные бренды

Lantronix PNT-SG3FS, Руководство пользователя по оборудованию

Результаты поиска

Содержание PNT-SG3FS

Отзывы:

Бренды по названию

Популярные бренды