Lantech IPWMR-3004DF Скачать руководство пользователя страница 4

 

3

 

 

FCC Warning 

 

This Equipment has been tested and found to comply with the limits for a 

Class-A digital device, pursuant to Part 15 of the FCC rules. These limits 

are  designed  to  provide  reasonable  protection  against  harmful 

interference in a residential installation. This equipment generates, uses, 

and  can  radiate  radio  frequency  energy.  It  may  cause  harmful 

interference to radio communications if the equipment is not installed and 

used in accordance with the instructions. However, there is no guarantee 

that interference will not occur in a particular installation. If this equipment 

does  cause  harmful  interference  to  radio  or  television  reception,  which 

can  be  determined  by  turning  the  equipment  off  and  on,  the  user  is 

encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the 

following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect  the  equipment  into an  outlet  on  a  circuit  different  from  that 

to which the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

 

CE Mark Warning 

 

This  is  a  Class-A  product.  In  a  domestic  environment  this  product  may 

cause radio interference in which case the user may be required to take 

adequate measures. 

Содержание IPWMR-3004DF



























Отзывы: