Lanner electronics IAC-F695 Series Скачать руководство пользователя страница 2

Страница: 2 / 51

OPYRIGHT

This document is copyrighted by the original manufacture. The original manufacturer

reserves the right to make modifications to the product(s) described in this manual at any

time without notice. This manual may not, in whole

or in part, be photocopied, reproduced, transcribed, translated, or transmitted in

whatever form without the written consent of the manufacturer, except for copies

retained by the purchaser for backup purposes. All rights are reserved.

RADEMARKS

Pentium

is a registered trademark of Intel Corporation.

The following are trademarks or registered trademarks of their respective companies:

IBM, Intel, AMD, Cyrix, Award, AMI, S3, Microsoft, Windows, Windows NT, Novell, SCO,

PC/104, PICMG, ALI, UMC, SMC, Winbond. Products mentioned in this manual are for

identification purposes only. All names of products or services appearing in this manual

are the trademarks or registered trademarks of their respective organizations and

companies.

Ver. No. 1.0
LEI-UM-IAC-F695 Series

Date: 6.01.2001

Содержание IAC-F695 Series




















































Результаты поиска

Содержание IAC-F695 Series

Отзывы:

Похожие инструкции для IAC-F695 Series

Бренды по названию

Популярные бренды

Lanner electronics IAC-F695 Series, Руководство пользователя

Результаты поиска

Содержание IAC-F695 Series

Отзывы:

Похожие инструкции для IAC-F695 Series

Бренды по названию

Популярные бренды