Lanier R/C Stinger 60 Скачать руководство пользователя страница 1

 

LANIER  R/C 

Stinger 60 

 

WARNING!  THIS IS NOT A TOY! 

 

THIS IS NOT A BEGINNERS AIRPLANE 

 

This R/C kit and the model you will build from it is not a toy!  It is capable of 
serious bodily harm and property damage. It is your responsibility, and 
yours alone - 

to build this kit correctly, properly install all R/C. components and 

flying gear (engine, tank, radio, pushrods, etc. and to test the model and fly it 
only with experienced, competent help, using common sense and in accordance 
with all safety standards as set forth in the Academy of Model Aeronautics Safety 
Code.  It is suggested that you join the AMA and become properly insured before 
attempting to fly this model.  If you are just starting R/C modeling, consult your 
local hobby dealer or write to the Academy of Model Aeronautics to find an 
experienced instructor in your area.                                                                                                    

Write to : Academy of Model Aeronautics, 5151 Memorial Dr, Muncie, IN 47302 

 

 

LIMITED WARRANTY 

 

Lanier R/C is proud of the care and attention that goes into the manufacture of parts for 
its model kits.  The company warrants that for a period of 

3

0 days, it will replace, at the 

buyers request, any parts or material shown to the company's satisfaction to have been 
defective in workmanship or material at the time of purchase. 
 
No other warranty of any kind, expressed or implied, is made with respect to the 
merchandise sold by the company.  The buyer acknowledges and understands that he is 
purchasing only a component kit from which the buyer will himself construct a finished 
flying model airplane.  The company is neither the manufacturer of such a flying model 
airplane, nor a seller of it.  The buyer hereby assumes the risk and all liability for 
personal or property damage or injury arising out of the buyers use of the components or 
the finished flying model airplane, whenever any such damage or injury shall occur. 
 
Any action brought forth against the company, based on the breach of the contract of 
sale to the buyer, or on any alleged warranty thereunder, must be brought within one 
year of the date of such sale, or there after be barred.  This one year limitation is 
imposed by agreement of the parties as permitted by the laws of the state of Georgia 
 
 

 
 
 
 

                                                                                          
                                                                      

1995 Lanier R/C Inc. 

Содержание Stinger 60

















Отзывы: