manualshive.com logo in svg

Lanier R/C STINGER 120 ARF, Руководство по сборке

Поделиться
Скачать
Lanier R/C STINGER 120 ARF Скачать руководство пользователя страница 10

Assembly Instructions

Lanier R/C, INC. P.O. Box 458 Oakwood, Ga. 30566 PH 770 532 6401

© copyright 1989 Lanier R/C

10

10

Place the gear over the holes with the

“rake” in the gear going to the rear. Insert
the 1/4-20x3/4” socket head screws
through the holes.

Secure the bolt on the inside of the fuse-

lage with a 3/4”x1/4” fender washer and
1/4-20 aircraft lock nut. Do not substitute
blind nuts here, the large fender washer is
important to keep the gear from pulling
out.

Install the axles in the pre-drilled holes in 

the landing gear using the aircraft lock-
nuts. Be careful and don’t over torque the
bolts or they will break easily. Install one of
the 3/16” wheel collars on the axel approx-
imately 3/16” in from the landing gear.
This will space the wheel in the middle of
the wheel pant. Adjust later if necessary.

The wheel pant has a 1/2” hole in one

side that will fit over the inside nut on the
axel. Slide the wheel pant and wheel on at
the same time and install the outside
3/16” wheel collar. You should file a flat
spot on the axel where the set screw for the
wheel collar fits. Screw the wheel pant to
the axel using the 3mmx18mm screw into
the blind nut on the inside of the wheel
pant. Be sure and use thread lock com-
pound on the screw. 

Locate the tail wheel
spring and cut into
two halves. Bend a
hook in each end. 

Attach one end to the tail wheel tiller and
the other to the inside hole on the rudder
horn. Do this on both sides. Attach the tail
wheel with the 1/8” wheel collar supplied.

Содержание STINGER 120 ARF





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды