Lang LGR36-NFR Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 24

Lang LGR36-NFR Скачать руководство пользователя страница 18

S

ERVICE

I

NFRARED

C

OMPACT

B

ROILER

P

AGE

18

OF

24

O

WNER

’

S

M

ANUAL

1192039

(10/09)

A

CCESS TO

S

ERVICEABLE

P

ARTS

Some serviceable parts are only accessible by removing body side panels and the front panel.

The main front panel is fastened with six sheet-metal screws. To remove the front panel, remove these screws, as
well as the burner-control-valve knob and the rack-height-position-lever knob. The main front panel can then be pulled
forward and removed. Each body side panel is fastened with two sheet-metal screws. Remove body-side screws and
slide the body side forward and away from the unit.

Figure 8

Access to Serviceable Parts

If necessary (or convenient), wall-mounted and flue-riser-mounted models can be un-mounted for servicing or repairs.
Use two people since the broiler weighs about 175 pounds (77 kilograms). Refer to the installation procedure in the
previous section of this manual for guidance.

A

DJUSTMENT OF

B

ROILER

P

ILOTS

The pilots are adjusted at the factory. If later the pilots are over-adjusted to the point where the flame is leaving its
port, or “blowing off,” the result is an unstable condition in which the pilot may extinguish. If necessary, adjust the
pilots using the following procedure:

1. If necessary, light the pilots.

2. Locate the pilot adjustment screw (which adjusts both pilots). It is a small slotted screw located on the pilot valve,

and is accessed though the slot in the front panel above the control-valve knob.

3. Turn the pilot adjustment screw to adjust the size of the pilot flames. The flame on each pilot should be large

enough to extend along the flame carrier to the burner surface.

A

DJUSTMENT OF

LOW

S

ETTING

The minimum gas flow of the burner control valve (which occurs when the valve is in the LOW position) is adjusted by
a setscrew in the hollow stem of the valve. Turn the setscrew clockwise to reduce the gas flow, or counterclockwise to
increase the gas flow. Adjust the screw so that when the broiler control knob is in the LOW position, the burner flames
do not flutter or “pop,” but rather burn with a dull red or a blue haze.

«
...
16
17
18
19
20
...
»

Содержание LGR36-NFR

























Отзывы:

Нет отзывов