Lang ECCO-T Скачать руководство пользователя

Страница: 44 / 71

TROUBLESHOOTING ECCO-PP, ECCO-PT CONT’D

NO MOTOR, MANUAL MODE

PROBABLE CAUSE

CORRECTIVE ACTION

Defective back-up toggle
switch

Confirm that toggle switch is in the “ON” position.

Check toggle switch for normal operation.

Defective back-up relay

Check for 208/240VAC at relay coil.

If no voltage is present:

Confirm that points are making.

If voltage is present:

Replace relay.

Defective component
transformer

Confirm that 208/240VAC is feeding primary coil.

Confirm that 24VAC is at secondary coil.

Defective motor relay

Check for 24VAC at relay coil.

If no voltage is present:

Confirm that points are making.

If voltage is present:

Replace relay.

Defective motor

Check for 208/240VAC across P1 and T7/T4.

If no voltage is present:

Confirm that wires have continuity.

If voltage is present:

Replace motor.

NO MOTOR, COMPUTER MODE

IMPORTANT NOTICE:

Before trying to trouble shoot “No Motor in Computer Mode” confirm that motor is

operational in “Manual Mode”.

PROBABLE CAUSE

CORRECTIVE ACTION

Defective output on CPU
board

Check for 24VAC at JP12 for high or JP13 for low (while oven is
calling for heat).

If no voltage is present:

Board is operating correctly.

If voltage is present:

Replace CPU.

https://appliancetechmanuals.com

Содержание ECCO-T








































































Результаты поиска

Содержание ECCO-T

Отзывы:

Похожие инструкции для ECCO-T

Бренды по названию

Популярные бренды

Lang ECCO-T, Руководство по обслуживанию

Результаты поиска

Содержание ECCO-T

Отзывы:

Похожие инструкции для ECCO-T

Бренды по названию

Популярные бренды