background image

7

 

UNPACKING 

Receiving the Oven 

Upon receipt, check for freight damage, both visible and concealed.  Visible 
damage should be noted on the freight bill at the time of delivery and signed by the 
carrier's agent.  Concealed loss or damage means loss or damage, which does not 
become apparent until the merchandise has been unpacked.  If concealed loss or 
damage is discovered upon unpacking, make a written request for inspection by the 
carrier's agent within 15 days of delivery.  All packing material should be kept for 
inspection.  

Do not return damaged merchandise to Lang Manufacturing 

Company.  File your claim with the carrier.

 

Location 

Prior to un-crating, move the oven as near to its intended location as practical.  The 
crating will help protect the unit from the physical damage normally associated 
with moving it through hallways and doorways. 

Un-crating 

The oven will arrive completely assembled inside a wood frame and strapped to a 
skid.  

Cut the straps and remove the wood frame.   

Remove Oven from skid and place in intended location. 

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

CAUTION 

EACH UNIT WEIGHS 430 LBS.  FOR SAFE HANDLING, INSTALLER SHOULD 
OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE MATERIALS 
HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR PALLET 
JACK) TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO THE 
PLACE OF INSTALLATION. 

 

CAUTION 

ANY STAND, COUNTER OR OTHER DEVICE ON WHICH OVEN WILL BE 
LOCATED MUST BE DESIGNED TO SUPPORT THE WEIGHT OF THE OVEN. 

 

CAUTION 

SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN 
CUT. 

 

 

 

Содержание ECCO-AP






















Отзывы: