background image

 

SAFETY SYMBOL

Model No.:

Serial No.:

Voltage:

1-Phase or 3 Phase:

Purchased From:

Location:

Purchase Date:

Installed Date:

These symbols are intended to alert the user to the presence of important operating 

and maintenance instructions in the manual accompanying the appliance.

FOR YOUR SAFTEY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN 

THE VICINTIY OF THIS OR ANY OTHER APPLIANCE.

The installation of the Appliance must conform to the NATIONAL FUEL GAS CODE "ANSI Z223.1 - LATEST 

EDITION" AND ALL LOCAL GAS COMPANY RULES AND REGULATIONS.
IN CANADA INSTALLATION SHALL BE IN ACCORDANCE WITH THE CURRENT CAN/CGA-B149.1 NATURAL 

GAS INSTALLATION CODE OR CAN/CGA-B149.2 PROPANE INSTALLATION CODE AND LOCAL CODES WHERE 

APPLICABLE.

POST IN PROMINENT LOCATION

INSTRUCTIONS TO BE FOLLOWED IN THE EVENT USER SMELLS GAS.  THIS INFORMATION 

SHALL BE OBTAINED BY CONSULTING YOUR LOCAL GAS SUPPLIER.  AS A MINIMUM, TURN 

OFF THE GAS AND CALL YOUR GAS COMPANY AND YOUR AUTHORIZED SERVICE AGENT.  

EVACUATE ALL PERSONNEL FROM THE AREA.

WARNING

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN 

CAUSE PROPERTY DAMAGE, INJURY OR DEATH.  READ THE INSTALLATION, OPERATION 

& MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS 

EQUIPMENT. 

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

DO NOT OPEN

WARNING, 

TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE 

CONTROL PANEL.  NO USER-SERVICABLE PARTS INSIDE.  

REPAIRS SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.

NOTICE

Using any part other than genuine Lang factory supplied parts relieves the manufacturer of all liability.
Lang  reserves  the  right  to  change  speci

 cations  and  product  design  without  notice.    Such 

revisions  do  not  entitle  the  buyer  to  corresponding  changes,  improvements,  additions  or 

replacements for previously purchased equipment.
Due  to  periodic  changes  in  designs,  methods,  procedures,  policies  and  regulations,  the 

specifications  contained  in  this  sheet  are  subject    to  change  without  notice.    While  Lang 

Manufacturing  exercises  good  faith  efforts  to  provide  information  that  is  accurate,  we  are 

not  responsible  for  errors  or  omissions  in  information  provided  or  conclusions  reached  as  a 

result of using the speci

 cations.  By using the information provided, the user assumes all risks in con-

nection with such use.

MAINTENANCE AND REPAIRS

Contact your local dealer for service or required maintenance.  Please record the model number, serial 

number, voltage and purchase & Installation Information in the area below and have it ready when you 

call to ensure a faster service. 

Содержание 224ZS

































Отзывы: