Lang 124ZT Скачать руководство пользователя страница 9

9

2M-W1823, Envirozone T

-Stat Electric Griddle

INITIAL START UP

Pre-Power On

Before starting the griddle for the first time, clean the griddle body and cooking surface.  

Use a mild soap and water solution, then rinse with clear water and dry.
The griddle is shipped with a protective coating and craft paper covering the cooking surface.   

This MUST be removed before heating the cooking surface.  After removing the craft paper, the coating 

can be scrapped from the cooking surface and then wiped with a dry cloth.

Power On

Set the temperature dials to 200°F (93°C).
Heat the griddle at 200°F (93°C) for 2 hours to evaporate any moisture that may be in the elements.
Wipe surface again with dry cloth to remove any residue that still remains.
After 2 hours at 200°F (93°C), turn the temperature up to 350°F (176°C) for ½ hour.
After the griddle reaches 350°F (176°C) for ½ hour, turn the griddle up another 50°F (10°C) for another 

½ hour and repeat this until it is at 450°F (232°C) for ½ hour.
The unit may emit a small amount of smoke as the cooking surface passes the 300°F (148°C) point.  

Do not be alarmed as the smoke is caused by oils associated with the manufacturing process and will 

stop when the griddle reaches 350°F (176°C).

Seasoning Cooking Surface

The cooking surface must be “seasoned” in order to eliminate product sticking during cooking.
To season, heat the griddle to 250°F (121°C).
Once at 250°F (121°C), coat the cooking surface with non-salted vegetable oil.
Allow the griddle to stand at 250°F (121°C) until the cooking surface looks dry then coat it again.
Heat the griddle to 350°F (176°C) and repeat the procedure.

NOTICE: 

During the first few hours of operation you may notice a small amount of 

smoke coming off the griddle, and a faint odor from the smoke.  This is 

normal for a new griddle and will disappear after the first few hours of use.

  

Содержание 124ZT





















Отзывы: