1
P
OWER
0
I
NPUT
B
ASS
C
LEAN
T
REBLE
G
AIN
G
AIN
D
RIVE
1
D
RIVE
2
B
RIGHT
M
ASTER
M
ASTER
B
ASS
M
IDDLE
T
REBLE
C
LEAN
D
RIVE
M
IDDLE
V
OLUME
C
LEAN
C
HANNEL
D
RIVE
1
D
RIVE
2
D
RIVE
E
QUALISATION
R
EVERB
TUBE
ENABLED
200
Controls the overall level on the drive1 channel. Use in conjunction with
The VScoop
switch drastically cuts out any mid frequencies present in the drive2 sound giving you a very modern,
aggressive lead tone.
Switch in to activate the drive2 channel. When active, control the amount of distortion with and the overall volume
with The centre of the switch will be lit when active.
Sets the level of gain on the drive2 channel. For optimum results the gain control should be used in conjunction with the
volume control . Setting low levels of gain with high levels of volume will result in a nice crisp blue’sy lead tone. Setting
the gain control to midway with a medium volume level will give you a punchy hard rock lead tone and setting the gain to
maximum and backing the volume off, gives you a full on metal lead tone. Obviously the type of guitar you use will have an
effect on the overall sound you hear.
Controls the overall level on the drive2 channel. Use in conjunction with
Controls the amount of bass or bottom end present on the two drive channels.
Controls the amount of mid present on the two drive channels.
Controls the amount of treble present on the two drive channels.
The ‘VTS Tone Shaping’ Radically alters the EQ of the amplifier by cutting some of the lower mid tones and carefully
boosting certain bass and upper mid frequencies. It is a global setting and may be used on any of the channels giving you
lots of different sound possibilities.
Sets the amount of reverb applied to the clean channel
Sets the amount of reverb applied to drive1 and drive2 channels.
Main power switch for the unit. Note: One of the three channel led’s will always be lit when the amplifier is switched on.
(Always switch off and disconnect the power cord when not in use)
10
14
15
15
14
This socket should be used for connecting your instrument to the amplifier. Only use a good quality screened cable.
Controls the volume level of the clean channel.
Adds brightness and sparkle to the clean channel when switched in.
Press in to activate the clean channel. The centre of the switch will be lit when active.
Controls the amount of bass or bottom end present on the clean channel.
Controls the amount of mid present on the clean channel.
Controls the amount of treble present on the clean channel.
The VScoop
switch drastically cuts out any mid frequencies present in the drive1 sound giving you a very modern,
aggressive lead tone.
Switch in to activate the drive1 channel. When active, control the amount of distortion with and the overall volume with
The centre of the switch will be lit when active.
Sets the level of gain on the drive1 channel. For optimum results the gain control should be used in conjunction with the
volume control . Setting medium levels of gain with high levels of volume will result in a nice crisp blue’sy lead tone. Setting
the gain control to 8-10 will give you a punchy hard rock lead tone. Obviously the type of guitar you use will have an effect on
the overall sound you hear.
10
11
11
1
Page 6 /12
Page 7 /12
2
3
4
12
15
16
FRONT PANEL CONTROLS
Laney
OPERATING INSTRUCTIONS
Laney
OPERATING INSTRUCTIONS
17
18
13
19
20
8
9
10
11
14
1
2
3
5
6
4
7
10
9
19
13
8
11
12 14
15
16
17
18
21
20
22
5
6
7
21
22
Содержание LV200
Страница 1: ...USER MANUAL LV200...
Страница 3: ...Page 3 12...
