CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
SUPPLY VOLTAGE
HT FUSE
CAUTION
TO REDUCE THE RISK OF FIRE REPLACE
ONLY WITH SAME TYPE AND RATING
MODEL
SERIAL NO.
1*16 OHM
MAXIMUM POWER CONSUMPTION
300 WATTS
WARNING - THIS APPARATUS MUST BE EARTHED
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER SERVICABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONEL.
ATTENTION REMPLACER LE FUSIBLE PR LE MEME
ET CALIBRE
ATTENTION DEBRACHER A LA PRISE SECTEUR AVANT D’OUVRIR
MADE IN THE U.K.
www.laney.co.uk
Laney
Power To The Music
T1A L
MAINS FUSE
~220-240V = T2A L 250V
~100-120V = T5A L 250V
1*8 OHM
1*4 OHM
2*16 OHM
2*8 OHM
L
OUDSPEAKERS
WARNING:
USE ONLY ONE IMPEDANCE
SELECTION AT A TIME
CLASS 2 WIRING MAY BE USED
IN
OUT
LINE
PREAMP
POWERAMP
FOOTSWITCH EL34
6L6/
5881
BIAS
ONLY FOR USE
WITH LANEY FS4
INSERT
RETURN
LEVEL
RETURN
SEND
BYPASS
SIDE/
CHAIN
INSERT
SEND
RETURN
RETURN
RETURN
EFFECTS LOOP
EFFECTS LOOP
OVERDRIVE CHANNEL B
CLEAN CHANNEL A
A+B
SEND
0
10
POWER INLET SOCKET:
Connect to your power source. Make sure the specified voltage is correct for your country!
POWER FUSE:
This is the main safety fuse for the unit. The fuse protects the AC power to the amplifier. USE ONLY THE
CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL. If a fuse blows or fails and a replacement of the
same size and rating is installed and it in turn blows, the amplifier has suffered a malfunction internally and needs immediate
service from a qualified technician. DO NOT TRY USING A FUSE OF HIGHER RATING. Using a fuse that is too large in
current rating may cause serious, irreparable damage to the amplifier and presents a serious fire hazard. The mains fuse
ratings are detailed in the specs section at the rear of this manual
HT FUSE:
This fuse protects the DC power to the tubes within the amplifier. USE ONLY THE CORRECT SIZE AND
RATING FUSE AS SPECIFIED ON THE PANEL. If a fuse blows or fails and a replacement of the same size and rating is
installed and it in turn blows, the amplifier has suffered a malfunction, at this point check the output tubes and replace faulty
ones if required. Should tubes not be the problem the amplifier should be checked out by a qualified technician. Do not try
using a fuse of greater value. Using a fuse that is too large in current rating may cause serious, irreparable damage to the
amplifier. Fuses are designed to protect, do not take chances.
LOUDSPEAKERS:
Loudspeaker outlets are provided on a series of five
jack sockets. The impedance of the
loudspeaker/s should be checked and connected to the appropriate socket/s. Using the incorrect sockets will reduce the life
of your output tubes and won’t sound as good and in extreme cases could damage your amplifier.
IMPORTANT:
Operation of your VH100R amplifier without a loudspeaker connected could result in expensive failure of
your output transformer.
DO NOT OPERATE WITHOUT A LOUDSPEAKER CONNECTED.
There are dedicated
optimised outputs for the following loudspeaker combinations: 1*16 ohm, 1*8 ohm, 2*16 ohm, 1*4 ohm, 2*8 ohm.
¼” (6.3mm)
Laney
OPERATING INSTRUCTIONS
Page 9 /20
37
37
51
51
35
35
38
38
36
36
34
34
0
V
H
1
0R
33
33
32
32
31
31
39
39
40
40
41
41
42
42
43
43
44
44
45
45
46
46
47
47
48
48
49
49
50
50
52
52
REAR PANEL CONTROLS