background image

9. Never charge battery in damp or wet environment.

10. Always charge battery at temperatures between32°F-120°F (0°C-49°).

11. Always store battery at temperatures between 32°F-86°F (0°C-30°C).

12. Always disconnect charger when battery is fully charged.

13. Never probe with conductive object.

14. Always fully charge battery before use.

15. Never completely discharge battery.

16. Always charge battery every six months if not in use.

CUT AND BURN HAZARD

To avoid injury to hands and fingers:

1. Always wear gloves, eye and ear protection.

2. Never short battery terminals because it may cause sparks or burns.

FALLING OR CRUSHING HAZARD

1. Never use pulling tool to secure a load.

2. Never shock load rope. Shock load can damage, overload and break rope.

3. Never use the pulling tool s rope to tow another vehicle or object. Impact 

loading during towing can exceed rope strength.

4. Always be certain the anchor you select will withstand the load and the strap 

or chain will not slip.

5. Always take time to use appropriate rigging techniques for pulling/lifting.

6. Never exceed pulling tool or rope capacity listed on product data sheet.

7. Never exceed the maximum pulling capacity as1000 Ib. (454 kg).

8. Only use low-stretch rope. Minimum diameter: 10mm (3/8"). Maximum 

diameter: 12mm (1/2").

9. Always use suitable anchor point capable of handling load.

10. Always use factory approved mounting hardware, components, and 

accessories.

11. Always avoid on/off cycles (jogging or plugging) puling tool This can 

damage motor controls and rope.

12. Always use a hook with a latch.

13. Always ensure hook latch is closed and not supporting load.

14. Never apply load to hook tip or latch. Apply load only to the center of hook.

15. Never use a hook whose throat opening has increased, or whose tip is bent 

or twisted.

16. Never use bungee straps that develop tremendous and potentially danger- 

ous amounts of force when stretched.

17. Always avoid side pulls which can pile up rope at one end of the drum. This 

can damage rope or pulling tool.

18. Never use puling tool to lift or move persons.

19. Warning make sure that your clothes are not going to get caught into the.

20. Danger never pull rolling objects that might roll out of youar control.

21. Caution do not touch the capstan drum immediately after operation as it will 

get hot and burn bare skin.

22. Caution visually inspect your rope before each usage. If it shows any sign of 

deterioration (cut strands, excessive abrasion) replace it.

MOVING PARTS ENTANGLEMENTHAZARD GENERAL SAFETY

1. Always Know Your Pulling Tool. Take time to fully read the Instructions 

and/or Operations Guide, in order to understand your pulling tool and its 

operations.

2. Never operate this puling tool when under the influence of drugs, alcohol or 

medication.

Содержание LWB0301













Отзывы: