Landoll Coulter Chisel 2112 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 108

background image

4-2

F-1102-0721

OPERATION AND MAINTENANCE

Tractor Preparation

The 2112 Coulter Chisel is designed to be pulled by
tractor equipped with a double lip or clevis type hitch. If
your tractor is not equipped as such, you need to
purchase the hitch from your local tractor dealer.

Before attaching the Coulter Chisel, prepare the tractor
as follows:

1.

Inflate the rear tractor tires equally and add ballast
according to the tractor operator’s manual.

2.

Lock the tractor drawbar in the center position.

Coulter Chisel Preparation

1.

Prior to operating the 2112 Coulter Chisel, inspect it
thoroughly for good operating condition.

2.

Replace worn or missing parts.

3.

When the machine is new, check the bolt tightness
after a few hours of operation. Tighten any loose nuts
or bolts. Check the lift wheel lug bolts daily.

4.

Check the lift wheel tire inflation. Inflate all tires
equally to avoid side draft. Follow the tire
manufacturer’s recommended pressures listed on the
sidewall of the tires.

5.

Lubricate the machine as shown in

“Lubrication

Maintenance” on page 4-11

and

“Lubrication

Table” on page 4-12

Attaching to the Tractor

1.

Align the tractor drawbar with the machine. Raise or
lower the Coulter Chisel ring hitch, as needed, using
the swivel jack. Attach the unit with proper size hitch
pin.

2.

Always place the swivel jack on the interior mount
before setting the machine in motion.

3.

Clean all hydraulic couplings and attach to the
tractor.

4.

Fully extend the hydraulic lift wheel cylinders, and
place the cylinder lockouts in the transport lock
position over the cylinder rods. Secure the lockouts
with the lockout pins.

«
...
86
87
88
89
90
...
»

Содержание Coulter Chisel 2112













































































































Отзывы:

Нет отзывов

Похожие инструкции для Coulter Chisel 2112

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: NEC Страницы: 29

Бренд: 1010music Страницы: 2

Бренд: 1010music Страницы: 4

Бренд: H&S Страницы: 42

Бренд: Safety 1st Страницы: 4

Бренд: Safety Engineering Страницы: 5

Бренд: Safavieh Страницы: 2

Бренд: Vendlet Страницы: 2

Бренд: XFit Страницы: 16

BlackBox Series

Бренд: Nakamichi Страницы: 23

Бренд: Harken Страницы: 4

Бренд: Abbriata Страницы: 27

Бренд: A&D Страницы: 33

Бренд: Masterclock Страницы: 19

Бренд: Tripp Lite Страницы: 24

Бренд: Hoist Fitness Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды