Landoll Coulter Chisel 2112 Скачать руководство пользователя страница 54

Страница: 54 / 108

3-16

F-1102-0721

ASSEMBLY INSTRUCTIONS

Auto Reset Shank Installation

Attach each shank to each auto reset clamp
assembly using 3/4 x 4 bolt, lock nut in bottom hole
and 3/4 x 5 bolt, lock nut in top hole

See

Figures 3-11

NOTE

For shallower depths, it may be necessary to move
shank into upper mounting holes. For certain
conditions shank may also be rotated forward when
using twisted shovels

Install the 2” cast flat point onto shanks with 1/2 x
3-3/4 bolts, 1/2 hd flat washers and 1/2 heavy nuts.

Install the 2” cast point onto shanks with 1/2 x 3-1/4
bolts, 1/2 hd flat washers and 1/2 heavy nuts.

Connect TW RH & LH shovels to each shank using
1/2 x 3 plow bolts, 1/2 hd flat washers and 1/2 heavy
nuts,

See Figures 2-4

through

2-9

for proper

locations of right hand and left hand shovels.

IMPORTANT

Right and left twisted shovels are determined by
direction of dirt flow when facing the direction of
travel.

NOTE

The center twisted shovel may be replaced with a
straight point.

Содержание Coulter Chisel 2112













































































































Результаты поиска

Содержание Coulter Chisel 2112

Отзывы:

Похожие инструкции для Coulter Chisel 2112

Бренды по названию

Популярные бренды

Landoll Coulter Chisel 2112, Руководство оператора

Результаты поиска

Содержание Coulter Chisel 2112

Отзывы:

Похожие инструкции для Coulter Chisel 2112

Бренды по названию

Популярные бренды