Landoll Brilllion Till'N Seed BPSB-8 Скачать руководство пользователя страница 71

Страница: 71 / 76

MAINTENANCE

F-1097-2305

4-19

TABLE OF CONTENTS

Troubleshooting

Problem

Solution

Machine is shaking or Tillage Rotor is bouncing

Reduce operating depth of Tillage Rotor

Increase air pressure in Air Shock

Machine is shaking and Drive Rotor is not Turning

Check if rotors are plugged

Check rotor drive chain

Drive Rotor is skidding

Check for items that maybe plugging rotors

Check rotor drive chain

Tillage Rotor Teeth plugging up with soil and vegetation

Soil is too wet for seeder operation

Tillage Rotor plugging with long grass

Grass is too wet or green for seeder operation

Uneven seed distribution or uneven stand

Check for plugged seed meters and drop tubes

Check to see if agitator is working properly

Seed is not coming out

Check if Transmission Drive Pins are in place

Check if seed is in Seed Box

Check if Transmission chains are properly adjusted

Содержание Brilllion Till'N Seed BPSB-8













































































Результаты поиска

Содержание Brilllion Till'N Seed BPSB-8

Отзывы:

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренды по названию

Популярные бренды

Landoll Brilllion Till'N Seed BPSB-8, Руководство оператора

Результаты поиска

Содержание Brilllion Till'N Seed BPSB-8

Отзывы:

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренды по названию

Популярные бренды