Landoll Brilllion Till'N Seed BPSB-8 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 76

background image

MAINTENANCE

F-1097-2305

4-15

TABLE OF CONTENTS

3.

Micro-Meter Box:

Individual Seed Meter Cups can

be adjusted as required. Adjustments can be made by
loosening the 1/4-20 x 5/8 Machine Screws that
mount the Seed Meter Cup to the Seed Box. Adjust
the affected Seed Meter Cup so the Feed Shutoff is
against the Seed Meter Cup Star Washer in the Seed
Meter Cup (closed). Be sure the Feed Roll stays
engaged in the Seed Meter Cup Star Washer.

Figure 4-21.

Figure 4-20: Micro-Meter

4.

Large Meter Box:

Individual Seed Meter Cups can

be adjusted as required. Adjustments can be made by
loosening the 1/4-20 x 5/8 Machine Screws that
mount the Seed Meter Cup to the Seed Box and the
1/4-20 Nut that attaches the Seed Meter Support to
the Seed Meter Cups.

See Figure 4-19.

Adjust the

affected Seed Meter Cup so the Feed Shutoff is
against the Seed Meter Cup Star Washer in the Seed
Meter Cup (closed). Be sure the Feed Roll stays
engaged in the Seed Meter Cup Star Washer.

Figure 4-21.

Check for binding by turning Seed Shaft.

After adjustments have been made seal the Seed
Meter Cups to Seed Box with clear Silicone.

Figure 4-21: Large Seed Meter

Servicing Metered Seed

Shafts

After you have serviced a Seed Shaft, Seed Meters or
related components you will need to Zero out the Seed
Meters to ensure that you are seeding uniformly.

“Seed Meter Adjustment” on page 4-14.

is a list of things to be conscience of when re-assembling
the Seed Shafts.
•

Ensure that the Washers are adjacent to Seed Meter
Feed Shutoffs.

See Figures 4-20

•

Ensure that the Seed Shaft can turn freely without any
binding when the Seed Meters are open or closed
after servicing. You may need to make adjustments to
the Seed Meter Supports at each Large Seed Meter.

Seed Meter Cup

Star Washer

Feed Roll

Washer

Seed Meter

Cup

Feed

Shutoff

Washer

Feed Shutoff

Seed Meter Cup

Star Washer

Feed Roll

Seed Meter

Cup

«
...
65
66
67
68
69
...
»

Содержание Brilllion Till'N Seed BPSB-8













































































Отзывы:

Нет отзывов

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренд: Qingdao H.Y Страницы: 6

Бренд: Raytech Страницы: 21

Бренд: Teac Страницы: 2

Бренд: laerdal Страницы: 2

Бренд: Baroness Страницы: 40

Бренд: Baroness Страницы: 40

Бренд: BARKO LOADERS Страницы: 85

Бренд: Datalogic Страницы: 48

Бренд: PageFlip Страницы: 32

Бренд: Federal Signal Corporation Страницы: 4

Бренд: FEBER Страницы: 2

Бренд: FASTERHOLT Страницы: 96

Бренд: Yardline Страницы: 75

Бренд: M-Audio Страницы: 12

Бренд: M-Audio Страницы: 64

Бренд: M-Audio Страницы: 16

Бренд: M-Audio Страницы: 4

Бренд: M-Audio Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды