Landoll Brilllion Till'N Seed BPSB-8 Скачать руководство пользователя страница 63

Страница: 63 / 76

MAINTENANCE

F-1097-2305

4-11

TABLE OF CONTENTS

Figure 4-13: Tillage Rotor Blade Repair - RH Side

15. Orient the Bearing Shield cup outward. Place the

appropriate Spacer, Bearing Shield, and 11ga
Washer on the Tillage Rotor Shafts.

16. Apply anti-seize on the Tillage Rotor Shafts. Install LH

and RH Swing Arms onto Drive Rotor and Tillage
Rotor Shafts.

17. RH side, place a 1.785 x 11ga Washer on the Drive

and Tillage Rotor Shafts. Install #80-2 Sprockets and
1/2" Keys onto Rotors. Larger Sprocket is on the Drive
Rotor.

18. RH side, secure the Drive and Tillage Rotors by

installing 3/4-10 x 2 Bolts, Lock Washers, and 3/4 x 3
x 3/8 Washers on the end of the Rotor Shafts.

19. LH side, secure the Drive and Tillage Rotor Shafts by

installing 3/4-10 x 2 Bolts, Lock Washers, 3/4 x 2-1/16
x 3/8 Washers, and Flat Top Washers on the end of
the Rotor Shafts.

20. Install Rotor #80-2 Drive Chain. Adjust Chain

Tension.

See “Chain Tension” on page 4-12.

21. Install chain access Cover to the RH Swing Arm.
22. Install Rotor Drive Chain Shield.
23. Insert the Gauge Wheel Hub and Spindle into the

Gauge Wheel Arm with 3/8-16 x 2-1/2 Bolts and
Locknuts.

24. Attach LH and RH Rockshaft Links to the Swing Arms

with 5/8-11 x 1-3/4 Bolts and Lock Washers.

25. Fill LH and RH Tillage Rotor Air Shocks with air.

See

“Air Shock” on page 3-6.

Rockshaft

Link

Gauge

Wheel Arm

Bolt,

3/4-10 x 2

Washer,

Lock 3/4

Washer,

3/4 x 2-1/16 x 3/8

Washer,

Flat Top

LH Swing

Arm

Tillage Rotor

Washer,

1.547 ID x 11ga

Front

Spacer,1.563 x

2.000 x 3.188

Bearing

Shield,1-1/2

U-Shape

Support Plate

Содержание Brilllion Till'N Seed BPSB-8













































































Результаты поиска

Содержание Brilllion Till'N Seed BPSB-8

Отзывы:

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренды по названию

Популярные бренды

Landoll Brilllion Till'N Seed BPSB-8, Руководство оператора

Результаты поиска

Содержание Brilllion Till'N Seed BPSB-8

Отзывы:

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренды по названию

Популярные бренды