manualshive.com logo in svg

Landoll Brillion Turfmaker II, Руководство оператора

Поделиться
Скачать
Landoll Brillion Turfmaker II Скачать руководство пользователя страница 42

2-26

9K998-0522

ASSEMBLY

Console w/Clutch Control 

Tractor Installation - Optional

1. Mount Angle Bracket onto Tractor where convenient 

for the operator. 

See Figure 2-41.

2. Attach Straight Bracket to Angle Bracket with 1/2-13 

x 1-1/2 Bolt and Flanged Ny-Lok Nut.

3. Attach the Console to the Straight Bracket with 

1/4-20 x 1 Bolt, Flat Washers and Locknut.

4. Plug Console 3-Pin Power Cord into the Tractor 

Convenience Outlet and 9-Pin Cord into the Seeder  
Harness.

5. Check clutch operation: Clutch will disengage when 

power is applied. (Clutch will make a clicking sound). 
Set seeder on the ground and drive a short distance 
while turning switch on and off. The seed shaft will 
stop rotating when switch is turned to 

"NO SEED"

 

position. 

See “Console w/Clutch Control - 

Optional” on Page 3-8.

Figure 2-41:  Console w/Clutch Control Tractor Installation

Bolt,1/2-13 X 1-1/2

Angle Bracket

Straight Bracket

Console

Locknut,1/4-20

Washer,Flat 1/4

Bolt,1/4-20 X 1

Washer,Flat 1/4

Locknut,

Flange 1/2-13 

SSP16 Monitor

3-Pin Power

Connector

9-Pin Amp
Connector

Содержание Brillion Turfmaker II













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды