Landoll BRILLION TURFMAKER II SL Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 100

background image

MAINTENANCE

9K998 4-3

Tires

8 Ft Seeder recommended Tire Size:

9.5L x 15, 8Ply Implement Rib Rating

Tire Inflation Pressure:

44 PSI

10 Ft and 12 Ft Seeder recommended Tire Size:

11L x 15, 12Ply Implement Rib Rating

Tire Inflation Pressure:

52 PSI

When Re-Installing 1/2-20 x 1 Wheel Bolts tighten to 50
ft-lbs using the sequence in

Figure 4-1.

Then tighten to

full torque of 80-85 ft-lbs.

Figure 4-1: Tightening Sequence

Wheel Hub Bearing Maintenance

Wheel Bearing maintenance should be performed at the
beginning of every season of use. Check the Wheel
Bearings periodically for excessive end play. If needed,
adjust or replace them using the following procedure:
1. Place the Frame on blocks or stands sufficient to lift

the Tire clear of the ground.

2. Remove the Tire.
3. Remove the Hub Cap, Cotter Pin and Slotted Nut.
4. Remove the Hub. Clean and inspect the Bearings

and Hub Cavity. Replace any worn or defective parts.

5. Repack the Bearings using a high-quality Wheel

Bearing Grease.

6. Slide the Single Lip Seal onto the Spindle. Do not

install the Seal into the Hub.

NOTE

The Single Lip Seals should point away from the Hub to
keep contaminants out and allow grease to pass.

7. Slide the Inner Bearing Cone and Hub onto the

Spindle.

8. Install the Outer Bearing Cone and Slotted Nut.

9. Tighten the Slotted Nut while rotating the Hub until

there is a slight resistance to wheel rotation. Then,
back the Slotted Nut off one notch, until the wheel
rotates freely without end play.

10. Slide the Single Lip Seal to the Hub and install the

Seal in the Hub.

11. Install a new Cotter Pin and re-install the Hub Cap.
12. Grease Wheels Hubs every 50 hrs.

Figure 4-2.

Lubrication Maintenance

• Oil Roller Chains periodically.
• All Seeders have Greaseable Bearings on the ends

of the Front and Rear Rollers and should be greased
every 20 hrs.

Figure 4-2.

• Pull Type Seeders Wheel Arm pivot point should be

greased every 4 hrs.

• Grease Wheels Hubs every 50 hrs.
• When the machine is not used for some time,

exposed portions of the Hydraulic Cylinder Rods
must be cleaned and covered with a thick coat of
grease to prevent corrosion, which will damage the
seal.

«
...
81
82
83
84
85
...
»

Содержание BRILLION TURFMAKER II SL





































































































Отзывы:

Нет отзывов

Похожие инструкции для BRILLION TURFMAKER II SL

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Keithley Страницы: 67

Бренд: Keithley Страницы: 23

Бренд: Keithley Страницы: 93

Бренд: Oki Страницы: 44

Бренд: Magnescale Страницы: 64

Бренд: R.M. Young Страницы: 10

Бренд: IBEX Страницы: 4

Бренд: LAZBOY Страницы: 9

Бренд: M-Audio Страницы: 3

Web Riderz MM00124 Web Swing

Бренд: M&M Sales Enterprises Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды