Landoll BRILLION TURFMAKER II SL Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 100

background image

OPERATION

9K998

3-7

Hydraulic Lift System

The Seeder is equipped with a Hydraulic Lift System to
raise and lower the unit in the field.



WARNING

Figure 3-8: Hydraulic Leak Detection

1. If the Hydraulic System is not filled with oil it should

be purged of air before transporting and field
operations. Carefully hitch the Seeder to the Tractor
and connect the Hydraulic Lift Hoses.

2. Disengage the Transport Locks.

See Figure 3-7.

3. Check to make sure the Tractor Hydraulic Reservoir

is full of the manufacturer’s recommended oil.

4. Slowly raise the machine until all Lift Cylinders are

fully extended. Lower and raise the unit to verify that
all Cylinders are working throughout the stroke. Fully
extend the Lift Cylinders and continue to hold the
lever until all Cylinder Rod movement stops.
Raise/Lower machine 5 times to purge air from the
system.

5. Do not loosen any Hoses or Fittings. Recheck

Tractor Reservoir to make sure it is within operating
limits.

6. Re-install Transport Locks.

See Figure 3-5.

Lift Circuit approximate oil requirement: .4 gallons.

Transmission Electric Clutch

IMPORTANT

At no time use high pressure water or air to clean the
Electric Clutch as damage could occur.

• The Electric Clutch

is controlled by a Toggle Switch

on the Clutch Switch Box that is mounted to the
Tractor.

•

The Electric Clutch

is disengaged when power (12

Volts) is applied. If there is a power failure or
electrical problem, the Seeder will continue to
operate, so the machine must be raised to stop
seeding.

• Seed Shafts will not rotate when the machine is

backed up.

• The

Clutch

Switch Box contains a 5 Amp Time-Delay

Fuse.

• The Electric Clutch must be disengaged (power

applied) when Seed Shafts are turned manually for
Calibration.

• Check Electric Clutch Operation. The Electric Clutch

will disengage when power is applied. (Clutch will
make a clicking sound). Set Seeder on the ground
and drive a short distance while turning Toggle
Switch to “Seed” and “No Seed”. The Seed Shaft will
stop rotating when Toggle Switch is turned to “No
Seed” Position.

• Turn Toggle Switch to “Seed” Position when Seeder

is not used to shut off power to prevent possible
overheating of Clutch Coil.

Escaping hydraulic fluid can cause serious
personnel injury. Relieve system pressure before
repairing, adjusting, or disconnecting. Wear
proper hand and eye protection when searching
for leaks. Use cardboard instead of hands (See
Figure 3-8.) Keep all components (cylinders,
hoses, fittings, etc.) in good repair.

«
...
63
64
65
66
67
...
»

Содержание BRILLION TURFMAKER II SL





































































































Отзывы:

Нет отзывов

Похожие инструкции для BRILLION TURFMAKER II SL

SACE Tmax XT Series

Бренд: ABB Страницы: 11

Бренд: Rangevision Страницы: 31

Бренд: Taber Страницы: 27

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGS Страницы: 5

Бренд: HAGER WERKEN Страницы: 2

Бренд: Yardline Страницы: 75

Pressure Governor

Бренд: Waterous Страницы: 53

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

Бренд: Jasco Страницы: 2

Бренд: Keller Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды