manualshive.com logo in svg

Landoll Brillion SL10, Руководство оператора

Поделиться
Скачать
Landoll Brillion SL10 Скачать руководство пользователя страница 67

MAINTENANCE

1P342-0621

4-5

Hydraulic Maintenance

IMPORTANT

Lower the unit to the ground, and relieve hydraulic 
pressure before attempting to service any hydraulic 
component.

WARNING

1. Check the tractor hydraulic fluid level per tractor 

owner's manual and after any leakage. Check fluid 
level with the Hydraulic Cylinders in the extended 
position.

2. If a Hydraulic Cylinder leaks, disassemble the parts 

to determine the cause of the leak. Any time a 
Hydraulic Cylinder is opened up, or whenever any 
Seal replacement is necessary, it is advisable to 
clean all parts and replace all Seals. Seal Kits are 
available from your Brillion dealer.

3. Check all Hydraulic Hoses weekly. Look for binding 

or cracking. Replace all worn or defective parts 
immediately.

4. Transport Locks are provided to hold the implement 

in a raised position. Do not attempt to perform any 
service work under the implement without first 
installing the Transport Locks.

 See Figure 3-5. 

Before servicing any hydraulic component, lower the 
machine to the ground and relieve all system 
pressure. If a hydraulic component is disconnected, 
repaired, or replaced, it will be necessary to purge 
the system of air before operation. 

See “Hydraulic 

Lift System” on Page 3-7.

Front and Rear Rollers

After an initial run of 5-10 hours, check the Front and 
Rear Roller Assemblies to ensure that the Wheels are 
tight to one another and that the Clamp Bands are tight. If 
not slide the Roller Wheels tight together and adjust the 
Roller Clamp Bands. Tighten the Clamp Band Socket 
Head Bolt (Clamp Band open section) over Roller Drum 
weld seam to 75 Ft-Lbs. Thereafter check Front and Rear 
Roller Assemblies every 50-100 hours.

IMPORTANT

To maximize seed germination, peaks on Rear Roller 
Wheels should line up with valleys on the Front 
Roller Wheels. This will require adjusting the Clamp 
Bands on each end of the Rear Roller Drum and 
moving the Wheels until valleys and peaks line up. 

NOTE

Failure to position the Clamp Band Socket Head Bolt 
(Clamp Band open section) over the Roller Drum weld 
seam will cause Clamp Band to loosen and slide.

Roller Adjustment Procedure

1. Adjust the Front Roller Wheels first. Loosen Clamp 

Bands and slide the Roller Wheels snug against 
each other, centering the entire assembly under the 
Deflector. 

2. Position the Clamp Band Socket Head Bolt (Clamp 

Band open section) over the weld seam on the Roller 
Drum. 

3. Slide the Clamp Band against the End Wheel on 

each end of the Roller and tighten the Clamp Band 
Bolt to 75 Ft-Lbs.

 See Figure 4-3.

Adjust the Rear Roller Wheels in the same manner as 
you adjusted the Front Roller Wheels except, start at the 
center of the Rear Roller and align the peaks of the Rear 
Roller Wheels with the valleys of the Front Roller Wheels. 
This will provide the best alignment of worn Roller 
Wheels.

Figure 4-3:  Clamp Bands

Escaping fluid under pressure can be nearly 
invisible and have enough force to penetrate the 
skin causing serious injury. Use a piece of 
cardboard, rather than hands to search for 
suspected leaks. Wear protective gloves and 
safety glasses or goggles when working with 
Hydraulic System.

Front Roller

Clamp Bands

Welded Seam

Welded Seam

Rear Roller

Содержание Brillion SL10













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды