Landoll 875-18 Скачать руководство пользователя страница 45

Страница: 45 / 64

3-14 WARNING LIGHTS INSTALLATION

3-14.1

Assemble lights to the warning light

bracket using 1/4-20 X 1-1/4 hex head cap

screws and hex lock nuts. Insure the wires

are in the groove in the base of the light to-

ward the mounting surface on the bracket.

Assemble one light for left side and one for

right side. The red light should be to the rear

with the amber light being the outer most

light.

3-14.2

Assemble mounting bracket angle to

warning light bracket assembly using 1/2-13

x 1-1/2 hex head cap screws and hex lock

nuts.

3-14.3

Assemble warning light bar and warning

light bracket assembly to outer rear of frame

as shown in

Figure 3-16

using 1/2-13 x

5-1/2 hex head cap screws and hex lock

nuts.

IMPORTANT

MAKE SURE LIGHTS ARE POSITIONED FOR

MAXIMUM VISIBILITY FROM THE REAR.

3-14.4

Install the rear warning light harness

between the lights.

Note: A 30" extension

is required to one side of rear warning

light harness on 15’F and 25’-6" models.

3-14.5

Install the main warning light harness

by starting at the hitch and routing the har-

ness through the hose loops to the rear

warning light harness.

3-14.6

Insure the harnesses are clear of any

moving parts and secure the harnesses with

tie wraps provided.

3-25

Figure 3-16 Electrical Installation

Содержание 875-18

































































Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды

Landoll 875-18, Руководство оператора

Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды