Landoll 5530 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 70

background image

4-10

F-524-0410 Edition

OPERATION AND MAINTENANCE

Compressor Operation

1.

The Grain Drill is equipped with a small air
compressor to make minor adjustments in system air
pressure

(See Figure 4-7.)

When making large

adjustments in system pressure, use shop or
alternate air source.

2.

Power to the electric air compressor is supplied
through the main lighting harness. Connect the
seven pin connector to the tractor. It is recommended
that the tractor be running while operating the
compressor to insure full system voltage to the
compressor. A toggle switch is located next to the
compressor to turn the compressor on and off.

3.

Operate the compressor only when making small
adjustments to the system air pressure. Do not
operate the compressor while planting. The
compressor filter is not sufficient to operate in the
dirty field conditions. The compressor also has a
limited duty cycle. Maximum run time for the
compressor is 5 minutes on followed by a 10 minute
off cool down period before additional operation.

4.

The air compressor is designed for oiless operation.
Thus there are no fluid levels to check or maintain.

Figure 4-7: Air Compressor Connection

12V DC AIR
COMPRESSOR

TOGGLE SWITCH

5530-aircom

«
...
28
29
30
31
32
...
»

Содержание 5530







































































Отзывы:

Нет отзывов

Похожие инструкции для 5530

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Бренд: Farmet Страницы: 102

Бренд: OHAUS Страницы: 84

Бренд: Tanaka Страницы: 20

Бренд: Tandem Страницы: 80

Бренд: Tanco Страницы: 4

Бренд: Stiga Страницы: 20

Zen-O lite RS-00600

Бренд: GCE Страницы: 20

Бренд: Kelso Страницы: 21

Бренд: Otto Bock Страницы: 52

Бренд: Torin BIG RED Страницы: 43

Бренд: Summit Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды