OPERATION OF L&L KILNS WITH A ONE-TOUCH™ (Deg F)
one-touch-operation-deg-f,pd
f
REV: 12/1/16
Page 5
2016
L&L Kiln Mfg, Inc. 505 Sharptown Rd, Swedesboro NJ 08085 P:856.294.0077 F:856.294.0070 [email protected] hotkilns.com
of that particular option.
7. Once you see the value you want press
ENTER
to
select and save.
8. The display will then cycle back to the starting display
of the control. (You will see
IdLE or StOP
alternating with a display of the current kiln temperature).
9. To change another option go through the process
again.
10. You can not change more than one option at a time.
9.2.2 EXAMPLE: CHANGE CONE OF BISQUE FIRE
Change the cone that the Bisque program goes to from
∆04 to ∆06:
1. Press the
BISQUE
Button for 5 seconds or more.
2. See
CndL
or
COnE
or
HLd
or
COOL
or
rStr
or
HtUP.
3. Release your finger from the button.
4. Scroll to
COnE
display by pressing the
UP
or
DOWN
button.
5. Press
ENTER
to change the value of the
COnE
option.
6. See
04
alternating with
COnE
7. Press the
DOWN
button until you see
06
8. Press
ENTER
9. See either
IdLE
or
StOP
alternating with a
display of the current kiln temperature.
9.2.3 EXAMPLE: CHANGE SPEED OF BISQUE FIRE
Change the speed of firing for the Bisque program from
Slow to Fast.
1. Press the
BISQUE
Button for 5 seconds or more.
2. See
CndL
or
COnE
or
HLd
or
COOL
or
rStr
or
HtUP.
3. Release your finger from the button.
4. Scroll to
HtUP
display by pressing the
UP
or
DOWN
button.
5. Press
ENTER
to change the value of the
HtUP
option.
6. See
SLO
alternating with
HtUP
7. Press the
DOWN
button until you see
FASt
8. Press
ENTER
9. See either
IdLE
or
StOP
alternating with a
display of the current kiln temperature.
Note - the temperatures, ramps and soak times that for
the various preset bisque and glaze programs, are shown
later on. These charts are for your reference only - when
you are using the Simple mode of operation - you can not
change any of those ramp and hold settings - just the overall
grouping of ramps and holds that makes up the “slow”,
“medium” and “fast” setting.
9.3 CUSTOM (Ramps and Holds):
1. Press
CUSTOM
and you have four Ramp/Soak
programs available for sophisticated custom
programming.
2. Each program has eight segments.
3. Each segment has a ramp, a temperature set point,
and a hold time for each segment.
4. See “CUSTOM RAMP/HOLD PROGRAMMING” later in
manual for detailed instructions on how to program in
the Custom mode of operation.
10. RESETTING FACTORY DEFAULTS
It is natural, when first learning a new technology, to get
confused or to put in something you are not sure of and then
not know where the beginning is. If you do this and you want
to go back to the factory defaults so you begin from scratch
do the following:
1. Press the
BISQUE
Button for 5 seconds or more.
2. See
CndL
or
COnE
or
HLd
or
COOL
or
rStr
or
HtUP
3. Release your finger from the button.
4. Scroll to
rStr
display by pressing the
UP
or
DOWN
button.
5. Press
ENTER
to change restore the control to its
factory default values
6. See either
IdLE
or
StOP
alternating with a
display of the current kiln temperature.
7. Repeat the same process for
GLAZE
11. HOW TO CANCEL A FIRING
1. Just press
ENTER
while the kiln is firing.