manualshive.com logo in svg

Land Pride STH2024, Руководство оператора

Поделиться
Скачать
Land Pride STH2024 Скачать руководство пользователя страница 18

Section 2: Adjustments

Table of Contents

12/10/18

STH2024 Spike Tooth Harrow 322-315M

14

Lift Cylinder Stop Nut Adjustment

Refer to Figure 2-1 & Figure 2-2:

The wings must be adjusted up or down to properly align 
guide bars (#2) with upper surface of wing support (#3). 
This is accomplished by turning stop nut (#5) towards lift 
cylinder (#4) to raise wings and away to lower wings. As 
pins wear and settle in, wings may droop a bit and need 
readjusting to make them once again slide onto the wing 
support properly.

Raising Wings with Stop Nut

Refer to Figure 2-1 & Figure 2-2:

1.

With harrow fully raised, fold wings in until the guide 
bars (#2) on both wings are about to make contact 
with the wing support (#3).

2. Slowly extend lift cylinder until guide bars (#2) on 

both wings are slightly below upper surface of wing 
support (#3).

3. Screw stop nut (#5) towards cylinder housing (#4) 

until stop nut is tight against cylinder housing.

4. Check fit-up by retracting wing cylinders until wing 

frames (#1) come against wing support (#3). Guide 
bars (#2) should slide smoothly onto the upper 
surface of the wing support and must be resting on 
the surface of the wing support. 

5. Apply a touch of silicone sealer (#6) between the 

cylinder threads and stop nut secure nut in place.

Lowering Wings with Stop Nut

Refer to Figure 2-1 & Figure 2-2:

1.

Unfold harrow and lower unit down to the ground.

2. Screw stop nut (#5) away from cylinder housing two 

or three full turns.

3. Raise harrow fully up and fold wings in until guide 

bars (#2) on both wings are positioned close to the 
wing support (#3).

4. Slowly retract lift cylinder until guide bars (#2) on 

both wings are slightly below the upper surface of 
wing support (#3).

5. Screw stop nut (#5) towards cylinder housing (#4) 

until stop nut is tight against housing.

6. Check fit-up by retracting wing cylinders until wing 

frames (#1) come against wing support (#3). Guide 
bars (#2) should slide smoothly onto the upper 
surface of wing support and must be resting on the 
surface of the wing support. 

7.

Apply a touch of silicone sealer (#6) between the 
cylinder threads and stop nut secure nut in place.

IMPORTANT:  

When folding wings, make sure guide 

bars (#2) slide smoothly onto wing support (#3) and 
is resting fully down on the flange of the wing 
support and not hanging above the flange.

After adjusting the stop nut, put a touch of silicone 
sealer (#6) between the threads and stop nut to 
prevent it from turning by vibration.

Section 2: 

Adjustments

Lift Cylinder Stop Nut Adjustment 

Figure 2-1

Lift Cylinder Stop Nut Adjustment 

Figure 2-2

33126

33122

Содержание STH2024

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды