Land Pride STH2024 Скачать руководство пользователя | Manualshive

Страница: 15 / 32

background image

Section 1: Assembly and Set-up

Table of Contents

STH2024 Spike Tooth Harrow 322-315M

12/10/18

11

Hydraulic Hook-up

WARNING

!

To avoid serious injury or death:

•

Shut power machine down and release all hydraulic

pressure to the equipment before connecting or

disconnecting hydraulic hoses to or from the power

•

Hydraulic fluid under high pressure can penetrate the skin

and/or eyes causing a serious injury. Wear protective gloves

and safety glasses or goggles when working with hydraulic

systems. Use a piece of cardboard or wood rather than

hands when searching for leaks. A doctor familiar with this

type of injury must treat the injury within a few hours or

gangrene may result. DO NOT DELAY.

Refer to Figure 1-4:

The double-acting wing cylinders (#1) should be attached
to a duplex outlet at the tractor with float capabilities to
allow the wings to float over the contour of the ground
while harrowing. The double-acting hydraulic lift cylinder
(#2) should be attached to a duplex outlet at the tractor
set for non-floating.

1.

Clean all dirt from tractor duplex outlets and all
hydraulic hose quick disconnect couplers (#8).

Refer to Figure 1-3:

2. Make certain wing cylinder hydraulic hoses (#10) are

routed through hose loops (#19, #20 & #21).

3. If tractor has float option on one of the duplex outlets,

connect hydraulic hoses (#10) to that outlet and set
duplex outlet in float position.

4. Make certain lift cylinder hydraulic hoses (#11) are

routed through hose loops (#19, #20 & #21).

5. Attach lift cylinder hydraulic hoses (#11) to a duplex

outlet of the operator’s choosing. If duplex outlet has
float option, set outlet to non-float.

Hydraulic Plumbing

Refer to Figure 1-4:

1.

Hydraulic wing cylinder 2" x 14" x 1 1/8" rod

2.

Hydraulic lift cylinder 3 1/2" x 8" x 1 1/4" rod

3.

Elbow, 3/4" MJIC x 3/4" MORB

4.

Orifice elbow, 1/32” orifice, 3/4MJIC 3/4MORB

5.

3/8" R2 Hydraulic hose, 48" long x 3/4" FJIC x 3/4" FJIC

6.

3/8" R2 Hydraulic hose, 59" long x 3/4" FJIC x 3/4" FJIC

7.

Tee, 3/4”JICBH x 3/4” MJIC x 3/4” MJIC

8.

Quick disconnect poppet type coupling, 3/4" MORB male

9.

Adapter, 3/4”FORB x 3/4” MJIC

10. 3/8" R2 Hydraulic hose, 191" long x 3/4" FJIC x 3/4" FJIC
11. 3/8" R2 Hydraulic hose, 198" long x 3/4" FJIC x 3/4" FJIC

Figure 1-4

33121

Tractor/Hydraulic Hook-up

Figure 1-3

33109

«
...
13
14
15
16
17
...
»

Содержание STH2024

































Отзывы:

Нет отзывов

Похожие инструкции для STH2024

Бренд: Bacharach Страницы: 48

Бренд: DB Industries Страницы: 60

Бренд: vc999 Страницы: 55

Бренд: Salsbury Industries Страницы: 4

Бренд: Nitecore Страницы: 4

MET ONE 3400 Series

Бренд: Hach Страницы: 48

Бренд: Tascam Страницы: 8

Бренд: Ransomes Страницы: 282

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Jacto Страницы: 64

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

EVENTWASH VL800

Бренд: Vari Lite Страницы: 23

Бренд: Vapotherm Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды