Land Pride SGC1560 Скачать руководство пользователя страница 18

Страница: 18 / 34

Section 1: Assembly & Set-Up

SGC1560, SGC1572, & SGC1584 Claw Grapples380-074M

4/4/23

Table of Contents

Connect Hoses to a Skid Steer or

Track Loader

•

Shut power machine down and release all hydraulic

pressure to the equipment before connecting or

disconnecting hydraulic hoses to or from the power

machine.

•

Hydraulic fluid under high pressure will penetrate the skin

or eyes causing serious injury. Wear protective gloves and

safety glasses or goggles when working with hydraulic

systems. Use a piece of cardboard or wood, rather than

hands, when searching for leaks. If an accident occurs, seek

immediate emergency medical care or gangrene may result.

DO NOT DELAY.

Refer to Figure 1-5:

1. Route hydraulic hoses (#4 & #5) through the most

convenient path to access your power equipment

couplers. Path shown may not be the most

convenient.

IMPORTANT:

Make sure coupler fittings on the

hydraulic hoses and power machine are clean

before connecting them together.

NOTE:

If attaching to a Kubota skid steer or track

loader, route hydraulic hoses through Kubota’s

Hose Stay as shown in Figure 1-6. Purchase

Hose

Stay #S6763

through your nearest Kubota dealer.

Refer to your power machine Operator’s Manual for

more instructions.

Kubota Hose Stay

Figure 1-6

2. Clean quick connect couplers (#6 & #7) of dirt, then

connect male and female couplers to the skid steer

outlets. Make sure quick connect couplers are fully

engaged. If they are not, check the following:
a. Make sure couplers are same size and type.
b. Make sure hydraulic pressure has been released.

3. Extend and retract hydraulic cylinders (#1) using the

power machine controls. If the cylinders operate in

the opposite direction intended, switch male and

female couplers (#6 & #7) on hoses (#4 & #5), then

reconnect couplers to the loader outlets.

4. For additional help, refer to hydraulic connection

instructions in your power machine Operator’s

Manual.

5. Continue with

“Check Equipment Clearances”

page 15.

Hose Stay Kit

70979

Connect Hydraulic Hoses to a Skid Steer or Track Loader

Figure 1-5

Bottom Slots

Return line (#5) terminates at

port (#2) in hydraulic cylinders (#1).

Pressure line (#4) terminates at

port (#3) in hydraulic cylinders (#1).

Top Angle Bars

Bottom Slots

35305

Содержание SGC1560



































Результаты поиска

Содержание SGC1560

Отзывы:

Похожие инструкции для SGC1560

Бренды по названию

Популярные бренды

Land Pride SGC1560, Руководство оператора

Результаты поиска

Содержание SGC1560

Отзывы:

Похожие инструкции для SGC1560

Бренды по названию

Популярные бренды