background image

8

Introduction

SC2660 & SC2672 Skid Steer Rotary Cutter   326-025M

4/24/12

Table of Contents

Owner Assistance

The Warranty Registration card should be filled out by
the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.

If customer service or repair parts are required contact a
Land Pride dealer. A dealer has trained personnel, repair
parts and equipment needed to service the Rotary
Cutter.

The parts on your Rotary Cutter have been specially
designed and should only be replaced with genuine Land
Pride parts. Therefore, should your cutter require
replacement parts go to your Land Pride Dealer.

Serial Number

Model No. _____________Serial No. _______________

For quick reference and prompt service, record model
number and serial number in the spaces provided above
and again on warranty page 33. Always provide model
number and serial number when ordering parts and in all
correspondences with your Land Pride dealer. Refer to
Figure 1 for location of your serial number plate.

Serial Number Plate Location

Figure 1

24539

Manual
Storage
Tube

Further Assistance

Your dealer wants you to be satisfied with your new
Rotary Cutter. If for any reason you do not understand
any part of this manual or are not satisfied with the
service received, the following actions are suggested:

1.

Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.

2.

If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.

3.

For further assistance write to:

Land Pride Service Department

1525 East North Street

P.O. Box 5060

Salina, Ks. 67402-5060

E-mail address

[email protected]

Содержание SC2672





































Отзывы: