20
Section 3: Operating Procedures
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
4/24/12
Table of Contents
safe operating procedures you do not understand,
please contact your nearest authorized dealer for a full
explanation and training session if necessary.
Skid Steer Operating Instructions
Assuming you have met all of the above requirements
and taken them seriously, it is time to take the next step
and that is accomplished by dressing appropriately for
the task. You will need to put on protective eye wear such
as safety glasses, goggles, or a face shield. A hard hat,
steel toed safety shoes, gloves, and hearing protection
are also highly recommended. Never wear loose fitting
clothing and you may want to put on a respirator or filter
mask to avoid breathing in dust, pollen, or agriculturally
used toxins that may be present.
The next step is a static or non-running pre-inspection of
the Skid Steer unit. You will want to make sure that the
Skid Steer is equipped with a fully functioning ROPS
(Roll Over Protection System) which does include seat
belts and an operator safety enclosure. The cab must
also be equipped with an Operator Protective Door,
which may have been supplied with the Skid Steer unit.
Land Pride does offer a protective door with the SC2660
and SC2672 if one is not provided by your skid steer
supplier. If the Skid Steer is to be operated on local
roadways, it must be equipped with appropriate Slow
Moving Vehicle (SMV) and other required lighting
packages so as to make it compliant with state and local
department of transportation requirements. The cutter
drive motor must be matched to the output of the
hydraulic capacity of the Skid Steer. Failure to do this
could result in serious over-speeding of the cutting unit
possibly resulting in serious injury, fatalities, or property
damage. The universal quick-hitch mount should be in
good working order and latches should be located to the
open position. There should be no evidence of hydraulic
leaks in and around the auxiliary hydraulic couplers.
There must be a readily accessible attaching point for the
Rotary Cutter lift-limit chain on the lower front portion of
the chassis frame. Finally make sure that all shields and
safety features are in place and fully functional.
The next step is to perform a running check of the Skid
Steer unit. As you get onto the Skid Steer and into the
operator’ compartment always use factory provided
hand-holds and don’t grab the steering or control levers
to ease or stabilize your entry. Fasten your seat belt once
you are seated and begin to mentally orient yourself with
the position of all controls, switches, pedals, levers, and
their related functions. Once you are sure that the park
brake is on, no people or animals are in close proximity,
all control levers, pedals, and hydraulic systems are in
neutral position, go ahead and start the engine. With the
engine now running and the throttle at approximately one
third, test all controls to make sure they are fully
functioning. If at any time there is an equipment failure,
shut the unit down and make immediate and full repairs.
Rotary Cutter Operating Instructions
Assuming all systems with the Skid Steer are “go” and
fully functioning, it is time to connect to the SC2660 or
SC2672 Rotary Cutter. This is done by maneuvering the
Skid Steer mounting plate into position under the
universal quick mount hitch saddle. Once this is
accomplished and the mower is fully supported by the
Skid Steer lift arms, lower mower to a point approximately
two inches above ground. Turn the engine off, set the
parking brake, and climb out of the Skid Steer. Lock the
latch handles down to engage the hitch pins. Make the
appropriate hydraulic connections to the auxiliary
hydraulic outlet and case drain making sure to keep
connectors clean. Be sure to use proper fittings and if
connection is difficult, moving levers may help relieve line
pressure. (Note! Hydraulic flow direction on all skid steers
is not the same. Make sure hoses are connected properly
or blades will rotate at a much slower speed.) Wipe away
spilled or excess hydraulic oil and secure Cordura sleeves
to contain potential leaks. Connect the height limiting
safety chain to the chassis attaching point and restrict
cutting height to no more that eighteen inches. This
completes the attachment of the cutter to the Skid Steer.
The next step is to complete a pre-operation check of the
cutter. Make sure all guards, safety shields, safety chains,
and deflectors are in place. All hardware must be in place
and appropriately tightened. Damaged, severely worn, or
defective parts must be replaced prior to operation. If your
unit is equipped with the optional front mounted gauge
wheel, you will want to adjust it for desired cutting height
at this time.
You should always inspect the area where you intend to
cut for debris and hazards located on the ground. No one,
including people and animals, should be allowed within
100 yards of this cutter when in operation. If someone
does approach, shut the cutter down immediately. The
blades on this cutter should never be allowed to come in
contact with objects such as wire, cable, rope, or chains
that might become entangled. These types of entangled
objects can become extremely hazardous by rotating
outside of the cutter deck housing resulting in serious
injury or death. Always inspect the area before you mow.
The best mowing results will be achieved at speeds
between 2 mph and 5 mph as grounds and mowing
conditions dictate. If you are mowing in particularly tall or
dense brush, you may want to make two passes with the
first pass being at 18" and the second pass made as a
cross-cut at the desired cut height. If you are mowing
without the benefit of the front mounted gauge wheel in
the float position, you will probably need to slow down
significantly especially over uneven terrain or furrows.
Driving too fast over uneven ground will cause the unit to
undulate in a forward pitching motion. The best advice is
to drive slow but keep engine speed and blade tip speed
high. Once you get the feel of it you can increase speed
and productivity.
When you do need to stop, make sure you set the park
brake, shut the Skid Steer engine off, and allow time for
the blades to stop rotating before you climb down. With a
little practice we are confident you will soon achieve safe
and excellent results with your new Land Pride SC2660 or
SC2672 Skid Steer Rotary Cutter.
