Land Pride SC2560 Скачать руководство пользователя страница 23

Страница: 23 / 44

1/15/21

SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M

Table of Contents

Section 2: Adjustments

Nominal Cutting Height

Figure 2-2

18"

Maximum Cut

Gauge Wheel

Ratchet Jack

Skid Steer

Lower Hitch Loop

Ground Level

Bottom of Rear

Skid Shoes

37995

Quick Link Coupler

Cutter Hitch Plate

Height Adjustment

Safety Chain

16.5"

Height Adjustment Safety Chain

WARNING

Always secure cutter deck in the up position with solid

supports or by locking the hydraulics before working around

or under a raised deck. Never work under equipment

supported by hydraulics. Hydraulics can drop equipment if

controls are actuated or if hydraulic lines burst. Either

situation can drop the cutter instantly even when power to the

hydraulics is shut off.

DANGER

Do not raise cutter higher than 16 1/2" off the ground. Raising

cutter higher can cause serious bodily injury and/or death.

Use safety limit chain to limit cutter height.

DANGER

Do not tilt hitch plate to raise front of cutter higher than the

rear. Raising front of cutter can cause serious bodily injury

and/or death.

Refer to Figure 2-2:

For safety, the cutter rear skid shoes should not be raised

higher than 16 1/2" off the ground (18" Maximum cutting

height).

1. Raise cutter’s rear skid shoes slightly less than

16 1/2" off the ground and set blocks under the four

corners of the cutter.

2. Run height adjustment safety chain from under the

2" x 3" hitch tube to the Skid Steer lower hitch loop.

Thread chain through the hitch loop and back

towards the hitch plate. Connect quick link coupler to

a chain loop as shown.

NOTE:

Two people may be required to install and

adjust the safety chain.

Kubota SVL

Figure 2-3

3. Raise cutter up until the safety chain is tight. Check

height of rear skid shoes.

4. If rear skid shoes are higher than 16 1/2" above

ground level, lower cutter and make necessary

adjustments to the safety chain to limit rear skid shoe

height to 16 1/2" maximum.

5. Tighten quick link coupler nut to secure safety chain.

NOTE:

When attaching the Rotary Cutter to a

Kubota SVL, height adjustment safety chain (#2)

should be looped around SVL tie-down bar (#1) and

adjusted so that the cutter cannot be raised over

16.5" off the ground as shown in Figure 2-3 below.

37386

Содержание SC2560













































Результаты поиска

Содержание SC2560

Отзывы:

Похожие инструкции для SC2560

Бренды по названию

Популярные бренды

Land Pride SC2560, Руководство оператора

Результаты поиска

Содержание SC2560

Отзывы:

Похожие инструкции для SC2560

Бренды по названию

Популярные бренды