Land Pride SC2560 Скачать руководство пользователя

Страница: 17 / 44

1/15/21

SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M

Table of Contents

Section 1: Assembly & Set-up

Figure 1-4

SC2572 Vented Dipstick

20822

Oil Level

Plug

Remove

Solid Plug

Install

Vented Dip

stick

DO NOT

OVERFILL!

IMPORTANT:

Rotary Cutters are shipped with a

solid plug in the gearbox to prevent loss of oil during

shipping and handling. The solid plug on top of the

gearbox must be replaced with a vented dipstick. Do

not operate cutter without vented dipstick installed.

SC2572 Motor and hose Assembly

Figure 1-3

SC2572 Motor And Hose Assembly

Your Skid Steer Rotary Cutter is factory supplied with one

of three motors mounted to the deck. Make sure you

check GPM rating on the hydraulic motor decal to verify if

it matches your Skid Steer’s GPM rating. Skip assembly

instructions below if the motor GPM rating matches your

Skid Steer.
See

“Motor and Hose Assemblies”

on page 26 to

properly select a motor that matches your Skid Steer.

Refer to Figure 1-3:

1. Remove fasteners (#7 & #8) and coupling

guard (#6). Keep fasteners and coupling guard for

reassembly of new motor.

2. Remove fasteners (#1 & #2). Keep fasteners for

reassembly of new motor.

3. Remove existing motor and hose assembly (#3).

Clean old gasket (#4) from mounting flange (#5).

4. Place new gasket (#4) onto mounting flange (#5).
5. Gently slide new motor and hose assembly (#3) onto

coupling (#10) with hoses extending towards the

hitch plate.

6. Secure hydraulic motor assembly with the four

existing 1/2"-13 x 2 1/4" lg. GR 5 hex head bolts (#2),

and 1/2"-13 hex flanged lock nuts (#1). Tighten nuts

to the correct torque. See

“Torque Values Chart for

Common Bolt Sizes”

on page 37.

Reattach coupling guard (#6) with 5/16" spring lock

washers (#8) and 5/16"-18 x 3/4" GR5 hex head cap

screws (#7). Tighten nuts to correct torque.

37942

Decal Location Stating

Motor GPM Rating

Содержание SC2560













































Результаты поиска

Содержание SC2560

Отзывы:

Похожие инструкции для SC2560

Бренды по названию

Популярные бренды

Land Pride SC2560, Руководство оператора

Результаты поиска

Содержание SC2560

Отзывы:

Похожие инструкции для SC2560

Бренды по названию

Популярные бренды