background image

Section 3: Adjustments

SBD3596 & SBD35108 Snow Blowers 370-347M

4/9/21

23

Table of Contents

Chute Rotation Gear Adjustment

Figure 3-3

Chute Rotation Gear Alignment

Refer to Figure 3-3:

1. Stop tractor, place gearshift in park, lower Snow 

Blower to ground, shut tractor engine off and remove 

switch key. Stay on tractor until power take-off has 

come to a complete stop.

2. Loosen all three hex head bolts (#6). Do not remove.
3. Move hydraulic motor mount (#3) as needed until 

drive gear (#2) has full tooth engagement with driven 

gear (#1).

4. Hold hydraulic motor mount (#3) in this position and 

tighten all three 3/8"-16 GR5 hex head bolts (#6) to 

the correct torque.

5. If removed, be sure to replace gear guard (#4) with 

existing 10-24 x 3/8" Type F pan head screws (#5), 

internal star washers (#7), and flat washers (#8). 

Tighten pan head screws.

35865

IMPORTANT: 

Gear guard (#4) is shown removed for 

clarity only. This adjustment can be made without 

removing the gear guard. Should the guard be 

removed, make certain it is replaced before putting 

the Snow Blower back into service.

Chute Rotation Adjustment

Figure 3-4

Chute Rotation

Refer to Figure 3-4:

WARNING

!

To avoid serious injury or death:  

Never rotate chute to throw snow at the tractor. The Snow 

Blower is capable of picking up large solid objects and 

discharging them out the chute causing serious bodily 

injury or death.

Never operate Snow Blower with chute blowing snow 

toward animals or people. The Snow Blower is capable of 

picking up large solid objects and discharging them out the 

chute at high speeds causing serious bodily injury or death.

1. Stop tractor and place gearshift in park before 

adjusting chute rotation angle. 

2. Push on hydraulic control lever to rotate chute to the 

left and pull lever to rotate chute to the right. 

3. Resume snow blowing once new chute angle is set.

Do Not Change Settings 

on Adjustment Screws 

for Hydraulic Motor.

35711

IMPORTANT: 

Never operate a Snow Blower with 

discharge chute throwing snow towards property 

such as vehicles, buildings, trailers etc. that can be 

scratched, dented or otherwise damaged by thrown 

projectiles.

IMPORTANT: Do not

 operate a Snow Blower 

throwing snow towards the tractor or operator. 

Repair chute rotation stop if discharge chute throws 

snow towards the tractor and/or operator. before 

putting the Snow Blower back into service.

IMPORTANT: 

Adjustment screws on hydraulic motor 

are preset at the factory. Do not change factory 

settings. Changing factory settings can cause 

structural damage to the Snow Blower.

Содержание SBD35108

















































Отзывы: