Land Pride SB10 Series, Руководство оператора

Страница: 34 / 42

32
Section 6: Maintenance & Lubrication
SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers 370-027M
2/11/21
Table of Contents
Lower Wear Bar Replacement
Figure 6-9
Lower Wear Bar (Optional)
Refer to Figure 6-9:
Inspect cutting edge wear bar and plow bolts for wear
and rotate 180
o
or replace as needed. Make sure wear
bar is replaced before auger housing becomes exposed
to wear.
1. Remove hex flange lock nuts (#3), plow bolts (#2),
and lower wear bar (#1).
2. Attach new wear bar (#1) to bottom of Snow Blower
frame with existing/new plow bolts (#2) and hex
flange lock nuts (#3).
3. Tighten lock nuts to the correct torque.
Long Term Storage
Clean, inspect, service, and make necessary repairs to
the Snow Blower when parking it for long periods and
when parking it at the end of a working season. This will
help ensure the Snow Blower is ready for field use the
next time you hook-up to it.
!
DANGER
Always disconnect driveline from tractor PTO before
servicing drive train components or underside of unit. Snow
Blower can be engaged if tractor is started causing bodily
injury or death.
33240
Lower Wear Bar Part Numbers
Part No. Part Description
370-108A WEAR BAR BUNDLE 1574 (Items 1, 2 & 3)
1. 370-213D LOWER WEAR BAR 1574
2. 802-603C 3/8"-16 x 1" GR 5 PLOW BOLT
3. 803-209C 3/8"-16 HEX FLANGE LOCK NUT
NOTE: When front edge of lower wear bar (#1) is
worn excessively, it can be rotated 180
o
and reused
to extend its’ wear life.
!
DANGER
Always secure Snow Blower in the up position with solid
supports before servicing underside of Snow Blower. Never
work under equipment supported by hydraulics. Hydraulics
can drop equipment if controls are actuated or if hydraulic
lines burst. Either situation can drop the Snow Blower
instantly even when power to hydraulics is shut off.
1. Clean off any dirt and grease that may have
accumulated on the Snow Blower and moving parts
and then wash surface thoroughly with a garden hose.
2. Check impeller, auger, wear bars, and skid shoes for
wear and breaks. Repair or replace if necessary. See
“Auger & Impeller Inspection”
on page 28.
3. Inspect for loose, damaged, or worn parts. Make
adjustments, repairs, and/or replace as needed.
4. Repaint parts where paint is worn or scratched to
prevent rust. Ask your Land Pride dealer for aerosol
touch-up paint. They are also available in touch-up
bottles with brush, quarts, and gallon sizes by adding
TU, QT, or GL to the end of the aerosol part number.
5. Replace all damaged or missing decals.
6. Lubricate as noted in
“Lubrication” starting on page
33.
7. Apply a coating of oil to the areas without paint due to
high wear to minimize oxidation.
8. Store Snow Blower on a level surface in a clean, dry
place. Inside storage will reduce maintenance and
make for a longer Snow Blower life.
9. Follow all “Unhooking Snow Blower” instructions
on page 18 when disconnecting Snow Blower from
tractor.
Ordering Replacement Parts
Land Pride offers equipment in factory standard beige
with black highlights. Equipment may also be purchased
in Orange. Special attention must be given to the part
number to prevent ordering the wrong color. A suffix
number corresponding to one of the colors below must
be added at the end of the part number. Parts ordered
without the suffix number will be supplied in factory
standard colors.
For example, if you are ordering a replacement part with
part number 555-555C and the existing part is orange,
then add the suffix 82 to the end of the number to make
the part number read 555-555C82.
Land Pride Aerosol Touch-up Paint
Part No. Part Description
821-011C PAINT LP BEIGE AEROSOL SPRAY CAN
821-002C PAINT LP BLACK AEROSOL SPRAY CAN
821-066C PAINT ORANGE AEROSOL SPRAY CAN
82 . . . . . . Orange 85 . . . . . . .Black