Land Pride SA20 Series Скачать руководство пользователя страница 21

Section 2: Operating Procedures 

Table of Contents

SA20 Hydraulic Post Hole Diggers 317-215M

3/8/18

17

Before leaving the operator’s seat, lower attachment to the 

ground and do a proper shutdown of the power machine.

Use the skid steer’s alternate emergency exit when exit 

passage through the front is blocked.

Do not use hand or foot controls for handholds or steps. 

Using them for handholds or steps can activate the controls.

Keep mud, snow, ice, and debris out of foot controls.

If included, raise restraint bar and move controls until both 

are locked and interlock system is activated.

Always secure equipment with solid supports before 

working under it. Never go under equipment supported by 
concrete blocks or hydraulics. Concrete blocks can break, 
hydraulic lines can burst, and/or hydraulic controls can be 
actuated even when power to hydraulics is off.

WARNING

!

To prevent serious injury or death:  

Allow only persons to operate this implement who have 

fully read and comprehended this manual, who have been 
properly trained in the safe operation of this implement, and 
who are age 16 or older. Serious injury or death can result 
from the inability to read, understand, and follow 
instructions provided in this manual.

Check hitch fit-up frequently to make sure loader hitch is 

properly positioned under the attachment’s top angle bar(s), 
lock handles are locked down with lock pins fully seated in 
their notches, and attachment is in good operating 
condition. An improperly attached unit can fall and be 
thrown toward bystanders and/or operator.
 

Operate only power machines equipped with a certified 

Roll-Over Protective Structure (ROPS) and seat belt. 
Fasten seat belt snugly and securely to help protect against 
serious injury or death from falling and machine overturn.

Always travel with adequate clearance between ground and 

auger. Hitting an object while traveling can damage 
equipment and cause operator to lose control.

Always travel with auger lowered to reduce the chances of 

tip over due to high center of gravity.

Do not install a bolt that is longer than what was originally 

supplied with the auger. Protruding hardware is more likely 
to entangle a bystander by catching on loose clothing.

This attachment has a 3500 psi maximum hydraulic 

pressure rating. Make sure your powered machine’s 
hydraulic pressure to this attachment does not exceed 3500 
psi. Exceeding this rating can result in equipment damage, 
serious injury, or death.

Do not use attachment to lift, carry, push or tow other 

equipment and objects. It is not properly designed or 
guarded for this use.

Never adjust tractor pressure relief valve for a pressure 

rating higher than what is recommended by the tractor 
manufacture.

Protect freshly dug holes immediately after digging by 

filling it with a post, covering the hole with a cover capable 
of supporting a person, or place a physical boundary 
around the hole to stop entry into the area.

Do not use post hole digger to wrap wire or any other items. 

Doing so can result in bodily injury and/or damage to the 
equipment.

CAUTION

!

To prevent serious injury:  

Auger tip gets hot after digging. Allow time for the tip to 

cool before touching or servicing the tip.

Dual-Angle Teeth

Refer to Figure 2-1 & Figure 2-2:

The Auger is shipped with teeth mounted at 40 degrees 
(see Figure 2-1). If you are experiencing difficulty in 
penetrating the soil, they can be turned over and 
mounted at 50 degrees (see Figure 2-2) for a more 
aggressive bite. Be sure to tighten all mounting hardware 
to the proper torque when securing teeth to the Auger. 
Se

“Torque Values Chart for Common Bolt Sizes” 

on 

page 32 for torque ratings.

Auger Teeth Mounted at 40 Degrees

Figure 2-1

Auger Teeth Mounted at 50 Degrees

Figure 2-2

25598

25598

Содержание SA20 Series







































Отзывы: