Land Pride RCM4715 Скачать руководство пользователя страница 30

Страница: 30 / 72

Section 1: Assembly & Set-up

RC(M)4715 & RCG(M)4715 Rotary Cutters 334-113M

6/3/20

Table of Contents

Hook-up LED Lights

Refer to Figure 1-27:

The lead wiring harness (#13) is equipped with a 7-pin

plug for connecting to the tractor’s 7-pin electrical outlet

shown in Figure 1-28.
1. Route lead wire harness (#13) through spring hose

loops (#14).

2. Connect plug on lead wire harness (#13) to the

tractor’s 7-pin electrical outlet.

3. It is best to have a second person verify the lights are

operating. Start tractor and operate lights as follows:
a. Turn on head lights to verify red lights illuminate.
b. Turn on flasher lights to verify amber lights are

blinking on and off.

Refer to Figure 1-29:

4. If the lights did not operate properly, recheck hook-up

of enhance module and wire harnesses. Make

necessary changes and repeat step 3 above.
a. Make sure connector (#9R) with a red wire is

connected to end labeled “ENHANCER” of wire

harness (#8R), for LED light on implement’s right

side.

b. Make sure connector (#9L) with a yellow wire is

connected to end labeled “ENHANCER” of wire

harness (#8L), for LED light on implement’s left

side.

c. Make sure connector on the lead wire harness

(#13) is connected to connector (#9C) on

enhancer module (#9).

d. Ensure that the 7-pin plug of 15'

lead wire harness

(#13) is properly seated inside 7-pin electrical

outlet on tractor (not shown).

5. Check wire harness routing to make sure wires will

not be pinched as wing decks are folded and

unfolded and while raising and lowering cutter height.

6. Secure harness in place with spiral hose wrap (#12)

and add cable ties as needed.

LED Hookup

Figure 1-27

72212

Tractor 7-Pin Electrical Outlet

Figure 1-28

Enhance Module Wire Connections

Figure 1-29

Remove Shipping Lugs

Refer to Figure 1-30:

Tie down lugs are installed on the rear two corners of the

center deck for shipping purposes only. They should be

removed and discarded before cutter is put into use.
Remove and discard both shipping lugs (#1) and

attaching hardware (#2 & #3).

Rear Shipping Lug Removal

Figure 1-30

72210

NOTE:

Some center axle options may have the

shipping lugs permanently integrated into them.

72468

Содержание RCM4715









































































Результаты поиска

Содержание RCM4715

Отзывы:

Похожие инструкции для RCM4715

Бренды по названию

Популярные бренды

Land Pride RCM4715, Руководство оператора

Результаты поиска

Содержание RCM4715

Отзывы:

Похожие инструкции для RCM4715

Бренды по названию

Популярные бренды