Land Pride RCM3712 Скачать руководство пользователя

Страница: 28 / 64

Section 1: Assembly & Set-up

RC(M)3712 & RCG(M)3712 Rotary Cutters 334-203M

11/6/18

Table of Contents

Unhook Rotary Cutter

See

“Long-Term Storage”

on page 45 when storing

the cutter for long periods and at end of season.

2. If power take-off is engaged, reduce tractor engine

speed to an idle and then disengage power take-off.

3. Park cutter on a level, hard surface. Place tractor

gear selector in park or set park brake.

Refer to Figure 1-27:

4. Wait for blades to come to a complete stop and then

raise cutter up and fold wings up to transport position.

5. Without relieving hydraulics, shut tractor off. See

“Tractor Shutdown Procedure”

on page 13.

DANGER

To avoid serious injury or death: Do not walk, stand, or allow

anyone else in the area where a raised wing will fall unless the

wing is securely locked in the raised position with its transport

lock.

6. Remove hairpin cotter (#1) from transport pin (#2)

and remove the transport pin (#2) from the light
guard bracket (#3).

Refer to Figure 1-28:

Insert transport pin (#2) through fold lugs (#3) and
secure it with hairpin cotter (#1).

Refer to Figure 1-29:

8. Spread stroke control spacers (#2) apart at the break

line and remove them from hydraulic cylinder (#1).

9. Start tractor and lower cutter until front skids are

resting on the ground or on support blocks.

10. Without relieving hydraulics, shut tractor down

properly before dismounting. Refer to

“Tractor

Shutdown Procedure”

on page 13.

WARNING

To avoid serious injury or death: Stay clear from underneath

the cutter and directly behind transport tires. The cutter could

fall suddenly causing the decks to lower and tires to roll back.

11. Replace stroke control spacers as needed to support

wheels at this position.

12. Move cylinder lift levers back and forth to release all

hydraulic pressure at the couplers.

Transport Pin, Storage Position

Figure 1-27

Transport Pin, Locked Position

Figure 1-28

Hydraulic Lift Cylinder and Stroke Control Spacers

Figure 1-29

Hydraulic Couplers & Wire Harness Storage

Figure 1-30

70463

70468

70487

Содержание RCM3712

































































Результаты поиска

Содержание RCM3712

Отзывы:

Похожие инструкции для RCM3712

Бренды по названию

Популярные бренды

Land Pride RCM3712, Руководство оператора

Результаты поиска

Содержание RCM3712

Отзывы:

Похожие инструкции для RCM3712

Бренды по названию

Популярные бренды