manualshive.com logo in svg

Land Pride RCM3615, Руководство оператора

Поделиться
Скачать
Land Pride RCM3615 Скачать руководство пользователя страница 28

Section 1: Assembly & Set-up

RC3615 and RCM3615 Series 2 S/N Rotary Cutters 330-502M

12/12/18

24

Table of Contents

Hook-up LED Lights

Refer to Figure 1-22:

The lead wiring harness (#13) is equipped with a 7-way 
round pin connector for connecting to the tractor’s 7-pin 
electrical outlet shown in Figure 1-23. 

1.

Route lead wire harness (#13) through spring hose 
loops (not shown).

2. Connect lead wire harness (#13) to the tractor’s 

7-way round pin receiver. 

3. It is best to have a second person verify the lights are 

operating. Start tractor and operate lights as follows:

a. Turn on head lights to verify red lights illuminate.

b. Turn on flasher lights to verify amber light are 

blinking on and off.

4. If the lights did not operate properly, recheck hook-up 

of enhance module and wire harnesses. Make 
necessary changes and repeat step 3 above.

5. Check wire harness routing to make sure wires will 

not be pinched as wing decks are folded and 
unfolded and while raising and lowering cutter height.

6. Add cable ties (#15) to wire harness as needed to 

secure the harnesses in place.

LED Hookup (Standard Clevis Hitch Shown)

Figure 1-22

Tractor 7-Pin Electrical Outlet

Figure 1-23

37594

Содержание RCM3615

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды