Land Pride RCM3615 Скачать руководство пользователя страница 24

Страница: 24 / 64

Section 1: Assembly & Set-up

RC3615 and RCM3615 Series 2 S/N Rotary Cutters 330-502M

12/12/18

Table of Contents

Driveline Assembly

DANGER

To avoid serious injury or death:
Make certain driveline yokes are securely fastened at each

end. A loose yoke can work free allowing the driveline to

rotate uncontrollably causing implement damage and bodily

injury or death to anyone nearby.

The main driveline can be constant velocity type or
conventional type. Pull-collar and bolted couplers are
used to secure the driveline to the tractor and implement
gearbox, respectively.

Refer to Figure 1-17:

Remove hex whiz nuts (#4A), carriage bolts (#3), and
shipping bracket (#2). Discard shipping bracket.

2. Slide driveline (#5) off end of shipping bracket (#1).

Set driveline aside for attaching to splitter box later.

3. Reinsert carriage bolts (#3) and secure with hex whiz

nuts (#4A). Tighten whiz nuts to the correct torque.

4. Remove hex whiz nuts (#4B), carriage bolts (#3), and

shipping bracket (#1). Discard shipping bracket.

IMPORTANT:

The driveline must be lubricated

before putting it into service. Refer to

“Lubrication

Points”

on page 48.

NOTE:

Wings must be lowered before removing the

driveline from its shipping location. See

“Unfold

Wings”

on page 19.

5. Reinsert carriage bolts (#3) and secure with hex whiz

nuts (#4B). Tighten whiz nuts to the correct torque.

Remove Main Driveline from Shipping Position

Figure 1-17

Refer to Figure 1-16:

6. Remove hand knobs (#8) and flat washers (#6).

Rotate front half of splitter guard (#3) open.

8. Remove and discard rubber shaft protector (#7) from

splitter gearbox shaft (#9).

9. Remove locknuts (#1) and bolts (#2) from bolted

coupler end of driveline (#4).

10. Attach bolted coupler end of driveline (#4) to splitter

gearbox input shaft with removed bolts (#2) and
locknuts (#1). Tighten locknuts to the correct torque.

37520

Driveline Assembly

Figure 1-16

37592

Содержание RCM3615

































































Результаты поиска

Содержание RCM3615

Отзывы:

Бренды по названию

Популярные бренды

Land Pride RCM3615, Руководство оператора

Результаты поиска

Содержание RCM3615

Отзывы:

Бренды по названию

Популярные бренды