Land Pride RCG3715 Скачать руководство пользователя

Страница: 52 / 66

Section 5: Maintenance & Lubrication

RC(M)3715 & RCG(M)3715 Rotary Cutters 334-114M

1/26/21

Table of Contents

Long-Term Storage

Clean, inspect, service, and make necessary repairs to

the cutter when storing it for long periods and when

storing it at the end of a working season. This will help

ensure the cuter is ready for field use the next time you

hook-up to it.

DANGER

To avoid serious injury or death:

•

Always disconnect driveline from the tractor before

servicing the drivetrain and components powered by the

drivetrain. A person can become entangled in the drivetrain

if the tractor is started and the power take-off is engaged.

•

Always secure equipment with solid, non-concrete supports

before working under it. Never go under equipment

supported by concrete blocks or hydraulics. Concrete can

break, hydraulic lines can burst, and/or hydraulic controls

can be actuated even when power to hydraulics is off.

1. Clean off any dirt and grease that may have

accumulated on the cutter and moving parts. Scrape

off compacted dirt from the bottom of deck and then

wash surface thoroughly with a garden hose. A

coating of oil or touch up paint may also be applied to

the lower deck area to minimize oxidation.

2. Check blades and blade bolts for wear and replace if

necessary. See

“Cutter Blades”

on page 46.

3. Inspect for loose, damaged, or worn parts and adjust

or replace as needed.

4. Repaint parts where paint is worn or scratched to

prevent rust. Ask your Land Pride dealer for aerosol

touch-up paint. Paint is also available in touch-up

bottles with brush, quarts, and gallon sizes by adding

TU, QT, or GL to the end of the aerosol part number.

5. Replace all damaged or missing guarding & decals.
6. Lubricate as noted in

“Lubrication Points”

starting

on page 49.

7. Store cutter on a level surface in a clean, dry place.

Inside storage will reduce maintenance and make for

a longer cutter life.

8. Follow

“Unhook Rotary Cutter”

instructions on

page 27 when disconnecting tractor from cutter.

Land Pride Aerosol Touch-up Paint

Part No.

Part Description

821-011C

PAINT LP BEIGE SPRAY CAN

821-070C

PAINT LP BLACK SPRAY CAN

821-054C

PAINT MEDIUM RED SPRAY CAN

821-058C

PAINT GREEN SPRAY CAN

821-066C

PAINT ORANGE SPRAY CAN

821-080C

PAINT GALVANIZED SPRAY CAN

Ordering Replacement Parts

Land Pride offers equipment in factory standard Beige

and factory standard Galvanized with black highlights.

This implement may also be purchased in Orange,

Green, Yellow or Red.
When ordering an optional color, the suffix number

corresponding to the color must be added at the end of

the part number. Parts ordered without the suffix number

will be supplied in factory standard colors.

For example, if you are ordering a replacement part with

part number 555-555C and the existing part is orange,

then add the suffix 82 to the end of the number to make

the part number read 555-555C82.

81 . . . . . . . Green

82 . . . . . . . Orange

83 . . . . . . . Red

85 . . . . . . . Black

86 . . . . . . . Yellow

Содержание RCG3715



































































Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды

Land Pride RCG3715, Руководство оператора

Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды