Land Pride RCF3696 Скачать руководство пользователя страница 40

Страница: 40 / 76

Section 2: Assembly of Optional Equipment

RCF3696, RCFM3696, RCF3610, & RCFM3610 Rotary Cutters 326-600M

Table of Contents

8/20/21

Chain Safety Guards (Optional)

DANGER

To avoid serious injury or death:
Rotary Cutters have the ability to discharge objects at high

speeds; therefore, the use of front & rear safety guards is

mandatory with this cutter. Double row chain guards should

be used when cutting along roadways and in areas where

people may be present. Stop blade rotation if bystanders are in

or around the area. It is recommended that a safety shield be

placed between the operator and cutter on an open air tractor.

WARNING

To avoid serious injury or death:
Keep all safety guards in place. Rotary Cutters have the

ability to discharge objects at high speeds. Use extreme

caution when cutting in areas where people may be present. It

is best to operate the cutter when no one is nearby. Stop blade

rotation if someone is in or around the area.

Front Chain Guards

Refer to Figure 2-2:

NOTE:

Do not tighten hardware until assemblies

are complete. Refer to

“Torque Values Chart”

page 70.

NOTE:

The two carriage bolts “A” are not used if CV

driveline option is included. See

“Constant Velocity

Driveline (Pull-Type)”

on page 33.

Front Chain Guard (RCF(M)3696 Single Chain Shown)

Figure 2-2

33953

Notched End

1. Locate Single or Double Chain Guards (#1 & #2) with

notched ends out. Attach chain guards and reflector

bracket (#5) to the deck with 1/2" -13 x 3 1/2" long

carriage bolts (#3) and hex whiz nuts (#4).

2. If Constant Velocity driveline is included, attach

bearing support to front chain guards using

steps 1 & 2 on page 33 for installation instructions.

3. Tighten hex whiz nuts (#4) to the correct torque.

Rear Chain Guard

Refer to Figure 2-1:

1. Install Single or Double Rear Chain Guard (#1) to the

deck rear with 1/2" -13 x 1 1/2" carriage bolts (#2),

and 1/2" flange nuts (#3).

2. Tighten hex whiz nuts (#3) to the correct torque.

Rear Chain Guard (RCF(M)3696 Double Chain Shown)

Figure 2-1

33954

Section 2: Assembly of Optional Equipment

Содержание RCF3696













































































Результаты поиска

Содержание RCF3696

Отзывы:

Похожие инструкции для RCF3696

Бренды по названию

Популярные бренды

Land Pride RCF3696, Руководство оператора

Результаты поиска

Содержание RCF3696

Отзывы:

Похожие инструкции для RCF3696

Бренды по названию

Популярные бренды