Land Pride RC4710 Скачать руководство пользователя страница 47

Страница: 47 / 72

Section 4: Options & Accessories

RC(L)4710 & RCM(L)4710 Rotary Cutters 334-863M

7/31/20

Table of Contents

Dual-Acting Lift Cylinder Accessory

Land Pride offers a Dual-Acting Lift Cylinder accessory

to allow the operator to lower the deck with hydraulic

power instead of gravity. The air vent in the lift cylinder is

replaced with a hydraulic fitting and hose. It is ideal for

dirty and corrosive environments, aiding in the

prevention of contaminants getting into the lift cylinder.

Dual-Acting Lift Cylinder Kit

334-927A . . . . . . . . Dual-acting lift cylinder accessory

Refer to Figure 4-9:

1. Remove vented plug (#1) from lift cylinder port hole.

Store plug away as it is no longer needed.

2. If attached, remove threaded end of hydraulic hose

(#3) from hydraulic fitting (#2).

3. Thread hydraulic fitting (#2) into lift cylinder port hole

as shown and tighten down. Be sure to orient

connecting end of hydraulic fitting (#2) toward the

front of cutter. Doing so will eliminate the potential of

a pinched hydraulic hose when cutter is in use.

4. With hydraulic fitting properly oriented, attach

hydraulic hose (#3) by tightening threaded end of

hose onto hydraulic fitting (#2).

Dual-Acting Lift Cylinder Accessory Hook-up

Figure 4-9

Remove

Install

72322

Lift Cylinder

Содержание RC4710









































































Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды

Land Pride RC4710, Руководство оператора

Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды