Land Pride RC4615 Скачать руководство пользователя страница 39

Страница: 39 / 68

Section 3: Operating Instructions

8/22/23

RC4615 & RCM4615 Rotary Cutters 331-644M

Transport Locks

Cutter wings will need to be raised and locked before
transporting on a roadway or servicing the deck
underside. If cutter wings are down, they will need to be
raised before transporting through narrow openings.

Disengage power take-off and wait for cutter blades
to come to a complete stop before raising wings.

Raise cutter wings fully up with hydraulics.

Place tractor gear selector in park, shut tractor
engine off or set park brake, remove switch key, and
dismount from tractor.

See Figure 3-2:

Remove hairpin

clip (#1) from storage lug (#2).

See Figure 3-3:

Rotate end of transport lock bar (#3)

to cylinder pin (#4). Secure with hairpin clip (#1).

Repeat steps 4 and 5 for the other wing. Your cutter is
now ready for transporting.

IMPORTANT:

Always disengage tractor’s power

take-off and wait for blades to come to a complete
stop before raising the wings to transport position.
Wing drivelines, wing gearboxes, and splitter
gearbox can be damaged if driveline is turning.

NOTE:

The wings are controlled with two hydraulic

lift cylinders. Be certain that the wing hydraulics are
attached to the tractor and the hydraulic hoses are
full of oil before proceeding.

Transport Bar, Storage Position

Figure 3-2

Transport Bar, Locked Position

Figure 3-3

27923

27921

Содержание RC4615





































































Результаты поиска

Содержание RC4615

Отзывы:

Похожие инструкции для RC4615

Бренды по названию

Популярные бренды

Land Pride RC4615, Руководство оператора

Результаты поиска

Содержание RC4615

Отзывы:

Похожие инструкции для RC4615

Бренды по названию

Популярные бренды