Land Pride RC4610 Скачать руководство пользователя страница 26

Страница: 26 / 68

Section 1: Assembly & Set-up

Table of Contents

1/14/19

RC4610 (540 RPM) and RCM4610 (1000 RPM): Rotary Cutters: 334-144M:

Driveline Assembly

DANGER

To avoid serious injury or death:

Make certain driveline yokes are securely fastened at each
end. A loose yoke can work free allowing the driveline to
rotate uncontrollably causing implement damage and bodily
injury or death to anyone nearby.

Refer to Figure 1-16:

The main driveline is constant velocity type with a
pull-collar for securing the driveline to the tractor power
take-off shaft.

Remove Main Driveline from Cutter

Figure 1-17

Refer to Figure 1-17:

Remove hex whiz nuts (#4A), carriage bolts (#3), and
shipping bracket (#2). Discard shipping bracket.

IMPORTANT:

The driveline must be lubricated

before putting it into service. Refer to

“Lubrication

Points”

on page 51.

37520

2. Slide driveline (#5) off end of shipping bracket (#1).

Set driveline aside for attaching to splitter box later.

3. Reinsert carriage bolts (#3) and secure with hex whiz

nuts (#4A). Tighten whiz nuts to the correct torque.

4. Remove hex whiz nuts (#4B), carriage bolts (#3), and

shipping bracket (#1). Discard shipping bracket.

5. Reinsert carriage bolts (#3) and secure with hex whiz

nuts (#4B). Tighten whiz nuts to the correct torque.

Refer to Figure 1-16:

6. Unsnap latches (#7) on both sides of gearbox

shield (#10) and remove gearbox shield without
unhooking chain attached to shield and mounting
plate (#4).

Remove and discard rubber shaft protector (#8) from
splitter gearbox shaft (#9).

8. Remove locknuts (#1) and bolts (#2) from bolted

coupler end of driveline (#5).

9. Align bolt holes in driveline coupler with grooves in

gearbox input shaft (#9).

10. Insert bolted coupler end of driveline (#5)

through gearbox shield (#10) as shown, and
attach to gearbox input shaft (#9) with removed
bolts (#2) and locknuts (#1). Tighten locknuts
to the correct torque.

11. Return gearbox shield (#10) to mounting plate (#4)

and secure with latches (#7).

12. Check safety chain (#3). Make sure it is latched to

mounting plate (#4) and gearbox shield (#10).

13. Rotate driveline hanger (#11) up and support

driveline (#5) on hanger. Final adjustments to hanger
will be made after tractor hook-up.

Driveline Installation

Figure 1-16

37599

Содержание RC4610





































































Результаты поиска

Содержание RC4610

Отзывы:

Бренды по названию

Популярные бренды

Land Pride RC4610, Руководство оператора

Результаты поиска

Содержание RC4610

Отзывы:

Бренды по названию

Популярные бренды