Land Pride RC4610 Скачать руководство пользователя страница 22

Страница: 22 / 68

Section 1: Assembly & Set-up

Table of Contents

1/14/19

RC4610 (540 RPM) and RCM4610 (1000 RPM): Rotary Cutters: 334-144M:

LP Performance Hitch Hook-up

DANGER

To avoid serious injury or death:

A crushing hazard exists while hooking-up and unhooking
implement. Keep people and animals away while backing-up
to implement or pulling away from implement. Do not operate
hydraulic controls while a person or animal is directly behind
the power machine or near the implement.

WARNING

To avoid serious injury or death:

The ball detent pin must be fully inserted into the park jack
with ball visible and popped out on the far side of the jack
before working on or around an unhooked cutter.

Refer to Figure 1-9:

Make certain park jack (#3) is properly attached to
the cutter hitch and secured with ball detent pin (#8).

2. Adjust park jack angle if it is not vertical. Refer to

“Align Park Jack Vertically”

on page 30.

3. If clevis hitch is not already supported horizontal,

rotate clevis (#9) horizontal and flip hitch holder (#11)
up so that its holes are on top as shown.

4. Insert customer-supplied hitch pin (#1) through holes

in hitch holder (#11) as shown in detail A. Secure with
hairpin cotter (#2).

5. Store center 3-point link in the tractor’s storage hook.

6. Start tractor, raise 3-point arms fully up, and carefully

back tractor within close proximity of clevis (#9).

NOTE:

Hitch pin (#1) and hairpin cotter (#2) are

customer supplied.

Shut tractor down properly before dismounting. Refer
to

“Tractor Shutdown Procedure”

on page 16.

8. Verify tractor drawbar is adjusted correctly. Refer to

“Drawbar Set-up”

dimensions on page 14.

9. Raise or lower park jack (#3) to align clevis (#9) with

tractor drawbar. Drawbar should fit between lower
and upper plates of clevis.

10. Restart tractor and continue to back tractor up to

cutter hitch until holes in tractor drawbar and clevis
hitch (#9) are aligned.

11. Shut tractor down properly before dismounting.

12. Remove bushings in clevis if customer supplied hitch

pin diameter is larger than 1". See

“LP Performance

Hitch Hole Size”

on page 32 for instructions.

13. Remove hairpin cotter (2) and hitch pin (#1) from

hitch holder (#11) and rotate hitch holder down.

14. Attach cutter to tractor drawbar with hitch pin (#1) and

hairpin cotter (#2) as shown in detail B.

15. Lower park jack (#3) until hitch weight is supported

by tractor drawbar.

16. Remove park jack (#3) and attach it to the weight box

storage mount with ball detent pin (#8). Make sure
jack is stored with its base level or lower than the
head. See cover picture for correct positioning.

17. Attach hitch safety chain (#4) to the tractor. Adjust

chain length to remove all slack except what is
necessary to permit turning. Lock chain hook
securely to the safety chain.

18. Continue with

“Hydraulic Hook-up”

on page 20.

IMPORTANT:

Protect park jack by attaching it to the

weight box before moving the cutter. Make sure jack
is stored with its base level or lower than the head to
prevent water and freeze damage.

Tractor Hookup to LP Performance Hitch

Figure 1-9

37631

37298

Содержание RC4610





































































Результаты поиска

Содержание RC4610

Отзывы:

Бренды по названию

Популярные бренды

Land Pride RC4610, Руководство оператора

Результаты поиска

Содержание RC4610

Отзывы:

Бренды по названию

Популярные бренды