manualshive.com logo in svg

Land Pride RC3620, Руководство оператора

Поделиться
Скачать
Land Pride RC3620 Скачать руководство пользователя страница 44

Section 5: Maintenance & Lubrication 

RC3620 & RCM3620 Rotary Cuters 330-841M

9/25/18

40

Table of Contents

Skid Shoes

WARNING

!

To avoid serious injury or death:  

Excessive wear on skid shoes may cause inadequate operation 
of cutter and create a safety hazard.

There is one skid shoe mounted on each wing deck and 
two skid shoes mounted on the center deck. Check all 
skid shoes for wear and replace if necessary. Order only 
genuine Land Pride parts from your local Land Pride 
dealer.

Center Skid Shoe

Refer to Figure 5-2:

Replace center skid shoes as follows:

1.

Remove 1/2" hex whiz nuts (#4), 1/2" hex bolts (#3), 
and center skid shoes (#2) from center deck (#1). 

2. Attach new skid shoes (#2) to cutter with existing 

1/2"-13 x 2" GR5 hex bolts (#3) and secure with 1/2" 
hex whiz nuts (#4). Tighten whiz nuts to the correct 
torque.

Wing Skid Shoe

Refer to Figure 5-3:

1.

Remove 3/8" whiz nuts (#5A), carriage bolts (#4), 
and hardened skid shoes (#2) from both wing decks.

2. Remove 3/8" whiz nuts (#5), plow bolts (#3), and 

wing skid shoes (#1) from both wing decks. 

3. Inspect plow bolts for wear and replaced if needed.

4. Inspect skid shoes (#1) and hardened skid 

shoes (#2) for wear. If skid shoes can be reversed 
and reused, reattach existing skid shoes to the 
opposite wing deck.

5. Attach new/existing hardened skid shoes (#2) to 

cutter side panels with removed 3/8"-16 x 1 1/4" GR5 
carriage bolts (#4) and whiz nuts (#5A). Do not 
torque nuts tight at this time.

6. Attach new/existing skid shoes (#1) to cutter side 

panels with new/existing 3/8" -16 x 1 1/4" GR5 plow 
bolts (#3) and hex whiz nuts (#5). 

7.

Tighten whiz nuts (#5 & #5A) to the correct torque.

NOTE:  

Wing skid shoes can be reversed and 

mounted on the opposite wing to increase their life.

Center Skid Shoe

Figure 5-2

Wing Skid Shoe

Figure 5-3

33872

#

Part No.

Description

2 330-802H CENTER SKID SHOE

39151

#

Part No.

Description

1 330-835D WING SKID SHOE
2 331-120H HARDENED WING SKID SHOE
3 802-466C PLOW 3/8-16X1 1/4 GR5
4 802-155C RHSNB 3/8-16X1 1/4 GR5
5 803-198C NUT HEX WHIZ 3/8-16 PLT

Содержание RC3620

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды