manualshive.com logo in svg

Land Pride RC3620, Руководство оператора

Поделиться
Скачать
Land Pride RC3620 Скачать руководство пользователя страница 27

Section 1: Assembly & Set-up 

RC3620 & RCM3620 Rotary Cuters 330-841M

9/25/18

23

Table of Contents

Wing Set-up for Shipping

Figure 1-20

Relocate Wing Lift Cylinder Mounts

Refer to Figure 1-20:

The rephasing lift cylinders are shipped from the factory 
moved forward 2 1/2". Mounting brackets (#1) must be 
relocated 2 1/2" rearward on both wings as follows:

1.

With wings unfolded, lower cutter down until right 
wing is resting on its skid shoe and transport 
wheel(s). If needed, place a support block under the 
wing skid shoe to ensure right wing is resting on its 
skid shoe and transport wheels. 

2. Shut tractor down properly before dismounting. Refer 

to 

“Tractor Shutdown Procedure” 

on page 17.

3. Move tractor hydraulic deck lift control lever back and 

forth several times to relieve all hydraulic pressure in 
the deck lift hydraulic system.

4. At the right-hand wing, remove all five whiz nuts (#3), 

cap screw (#5) and four carriage bolts (#2). Keep 
carriage bolts and four hex whiz nuts (#3) for reuse. 
Discard cap screw (#5) and one hex whiz nut (#3).

5. Remove mounting bracket (#1) from between 

mounting ears (#4).

6. Using tractor control lever, fold wing deck up high 

enough to place a support block under its skid shoe. 
Use a 4" support block if cutter is equipped with 
21" laminated tires and a 6" support block if cutter is 
equipped with 29" aircraft tires. 

7.

Unfold wing deck until its skid shoe is resting on the 
4" or 6" support block.

35222

Wing Set-up for Field Use

Figure 1-21

Refer to Figure 1-21:

8. Extend or retract hydraulic lift cylinder on the wing 

until rear holes “A” in mounting bracket (#1) are slight 
back of holes “A” in mounting ears (#4). 

9. Attach a hoist or jack under the right-hand wing 

wheel axle and raise wheels up until carriage bolts 
(#2A) can be inserted. If needed, use a drift punch to 
align rear holes “A”.

10. Insert rear carriage bolts (#2A) as shown and install 

hex whiz nuts (#3A). Draw nuts up snug, do not 
tighten at this time.

11. Use a drift punch in holes “C” to align the front 

holes “B”.

12. Insert front carriage bolts (#2B) in holes “B” as 

shown and install hex whiz nuts (#3B).

13. Tighten hex whiz nuts (#3A & #3B) to the correct 

torque.

14. Remove hoist or jack from under the transport 

wheels.

15. Fold wing up, remove support block from under its 

skid shoe, and return wing to its unfolded position.

16. Repeat steps 1-15 for the left wing.

35223

Содержание RC3620

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды