manualshive.com logo in svg

Land Pride RC3620, Руководство оператора

Поделиться
Скачать
Land Pride RC3620 Скачать руководство пользователя страница 45

Section 5: Maintenance & Lubrication 

RC3620 & RCM3620 Rotary Cuters 330-841M

9/25/18

41

Table of Contents

Cutter Blades

DANGER

!

To avoid serious injury or death:  

•

Always disconnect driveline from the tractor before 

servicing the drivetrain and components powered by the 
drivetrain. A person can become entangled in the drivetrain 
if the tractor is started and the power take-off is engaged.

•

Always secure equipment with solid, non-concrete supports 

before working under it. Never go under equipment 
supported by concrete blocks or hydraulics. Concrete can 
break, hydraulic lines can burst, and/or hydraulic controls 
can be actuated even when power to hydraulics is off.

WARNING

!

To avoid serious injury or death:  

•

Do not operate cutter with blades that are out-of-balance, 

bent, excessively worn, excessively nicked, or with blade 
bolts that are excessively worn. Such blades can break loose 
at high speeds.

•

Wait for blades to come to a complete stop before accessing 

blade bolts through blade bolt access hole.

•

Wear eye protection and gloves while inspecting, removing, 

sharpening, and replacing a blade.

•

Do not attempt to straighten a bent blade or weld on a 

blade. Do not attempt to modify a blade such as hard 
surfacing, heat treating, cold treating, or by any other 
method. Always replace blades with new Land Pride blades 
to assure safety.

Always inspect cutting blades before each use. Make 
certain they are properly installed and in good working 
condition. Replace any blade that is damaged, worn, 
bent, or excessively nicked. Never try to straighten a bent 
blade! Small nicks can be ground out when sharpening. 

Remove cutting blades and sharpen or replace as 
follows:

1.

Park on a level, solid surface. Place tractor in park or 
set park brake. Unfolded wing decks until they are 
resting on the ground. Fully extend deck lift cylinders 
to lift center and wing decks up.

2. With wings unfolded and deck lift cylinders fully 

extended, shut tractor down. Refer to 

“Tractor 

Shutdown Procedure” 

on page 17.

3. Place solid support blocks under the decks. 

4. Start tractor and retract deck lift cylinder until the 

center and wing decks are resting securely on the 
support blocks. 

IMPORTANT: 

Cutting blades must be replaced in 

mating pairs. Not replacing both blades will result in 
an out-of-balance condition that will contribute to 
premature bearing breakdown on the spindle hub 
and create structural cracks in the cutter housing.

Содержание RC3620

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды